Shared Strategies Forum - Published: We use strategies across three products that are very similar. I’d like to share as much code as possible between all three strategies so that changes to one shared chart are reflected in the others. Is...moreWe use strategies across three products that are very similar. I’d like to share as much code as possible between all three strategies so that changes to one shared chart are reflected in the others. Is this limited to just shared subroutines or are there other mechanisms to share across strategies?... <less Hide Title bar in Groov view Forum - Published: Is there a way to Hide the title bar from certain users?...Is there a way to Hide the title bar from certain users?... <less SNAP-ODC-32-SRC to SNAP-UDC-HDB Ribbon Cable Alternative Forum - Published: My goal is to have the SNAP-UDC-HDB near the SNAP-ODC-32-SRC module, within 6" -12" inside the same electrical enclosure. Opto 22 sells the cables at 6ft lengths, this works great when you have the PAC...moreMy goal is to have the SNAP-UDC-HDB near the SNAP-ODC-32-SRC module, within 6" -12" inside the same electrical enclosure. Opto 22 sells the cables at 6ft lengths, this works great when you have the PAC Rack separated from the SNAP-UDC-HDB at that distance. I researched for an alternate method of connecting them. Turns out that a 40 pin hard drive cable works! I purchased 12" length cables for $6 each. Note the cable must have pin 20 open, not filled in for it to work. Attached is how I connected...... <less Trane Chiller UC800 Controller Inerface Forum - Published: Just seeing if anyone out there has successfully interfaced a trace chiller UC800 controller to Opto via either Modbus or BACNET?? Currently having a few issues with both. Modbus im using a mgate modbus...moreJust seeing if anyone out there has successfully interfaced a trace chiller UC800 controller to Opto via either Modbus or BACNET?? Currently having a few issues with both. Modbus im using a mgate modbus gateway to convert the Modbus RTU to Modbus TCP/IP. Im using modbus poll to check the data coming out and all that it keeps coming back with illegal packet length. Bacnet I can see the UC800 and can read the object names but cant read any of the actual values. I can see both object names and valu...... <less RIO Node-Red Listening on non-standard port Forum - Published: Hello, I have my device IO figured out on a RIO. Next step is getting TCP listener to work. The flow I am working on needs to listen on a specific port for a message. I am using ETH-0. The application...moreHello, I have my device IO figured out on a RIO. Next step is getting TCP listener to work. The flow I am working on needs to listen on a specific port for a message. I am using ETH-0. The application residing on another machine will simple open a connection to the RIO and send messages to it for the RIO to take actions. When I deploy the TCP listener to listen to a port number less than 1024 I get a permission denied. I attempted to add a firewall rule on the RIO to for the subject port and ...... <less OptoMMP Tool kit? Forum - Published: Is this version specific? i.e. Can the latest version be used with Pac Control 8.5? Which version has ActiveX controls that supports Legacy VisualBasic applications (VB 6.0)? Thanks....Is this version specific? i.e. Can the latest version be used with Pac Control 8.5? Which version has ActiveX controls that supports Legacy VisualBasic applications (VB 6.0)? Thanks.... <less Groov EPIC-PR1 - Restful API Forum - Published: Hey Guys, I might be missing it, but is there no restful api for the EPIC-PR1 like the snap-pac-r1/r2? I know that we can build a similar function like it through node-red, but wouldn’t it make sense...moreHey Guys, I might be missing it, but is there no restful api for the EPIC-PR1 like the snap-pac-r1/r2? I know that we can build a similar function like it through node-red, but wouldn’t it make sense just to have it baked in as well? Saves a lot of work and testing. I am using a mixture of PR1 & R2’s, mainly because I need reliable serial comms for modbus RTU. Once the serial module is ready for the PR1, I will be swapping a lot and changing future builds. It would be nice to use my curren...... <less PAC Project Versions Forum - Published: Almost 95% of my projects were created with PAC Project version R9.6003-86. On one of my PCs, I must have used a more recent version maybe R9.6004-109, R9.6005-125 or R9.6006-131. First off, how can I...moreAlmost 95% of my projects were created with PAC Project version R9.6003-86. On one of my PCs, I must have used a more recent version maybe R9.6004-109, R9.6005-125 or R9.6006-131. First off, how can I tell which PAC Project this PC is running. (sure, I can see Control is R9.6e, Display is R9.6F Build 0092 and SoftPAC is v.R9.6a, but what Project version installed those?) Secondly, can I reinstall R9.6003-86 on this same PC and both versions will work (maybe in a different location on my PC)? L...... <less Max number of trends in a project? Forum - Published: Is there a maximum number of trends in a project? I keep trying to add one and the trend gadget just crashes/never loads in ‘View’. I have tried interactive and classic. trend_crash.png1068×329 21.3...moreIs there a maximum number of trends in a project? I keep trying to add one and the trend gadget just crashes/never loads in ‘View’. I have tried interactive and classic. trend_crash.png1068×329 21.3 KB The values to the left are the same values used in the trend.... <less Which groov EPIC Module for humidity sensor? Forum - Published: Hi Ma’am/Sir, May I ask if what module can read a humidity sensor? I have already created in our Data Center a Temperature Monitoring and used the GRV-ITMI-8 module. Thanks in advance. Best Regards, Jay...Hi Ma’am/Sir, May I ask if what module can read a humidity sensor? I have already created in our Data Center a Temperature Monitoring and used the GRV-ITMI-8 module. Thanks in advance. Best Regards, Jay... <less SNAP-OMR6 vs SNAP-ODC5R. Mechanical relay ouput modules Forum - Published: It still surprises me how many people work with Opto 22 hardware and software and yet are not signed up to OptoNews and so miss out on hearing all the cool stuff that happens in the world of Opto 22...moreIt still surprises me how many people work with Opto 22 hardware and software and yet are not signed up to OptoNews and so miss out on hearing all the cool stuff that happens in the world of Opto 22… Another topic for another day perhaps, right now I just want to answer a question about our new digital output modules which got announced in[URL=“http://www.opto22.com/site/optonews/2011/optonews_08312011.aspx”] last week’s OptoNews. SNAP-OMR6. 4 channels of 6 amp mechanical relay goodness, more th...... <less A pulse signal generated by the Holzer sensor Forum - Published: Excuse me, a pulse signal generated by the Holzer sensor, can use the IDC5 count? If not, what kind of module is used? Thank you...Excuse me, a pulse signal generated by the Holzer sensor, can use the IDC5 count? If not, what kind of module is used? Thank you... <less Fonts rendered at different sizes for different controls Forum - Published: I’ve come across a minor inconsistency with the size text is rendered for the Button control and the Text object. In typical WinForms applications these fonts would be displayed the same size if they...moreI’ve come across a minor inconsistency with the size text is rendered for the Button control and the Text object. In typical WinForms applications these fonts would be displayed the same size if they are configured to the same font size. I’ve attached a screen shot that illustrates the difference, both of these controls are set to: MS Sans Serif Bold 20pt Is this a known issue? different font sizes on controls.png818×506 8.23 KB Regards, Steve... <less Radio button-like behavior Forum - Published: Greetings OptoFans, I recently had someone ask me for some sample code to make use of a loop in OptoScript. In his application, he has several user choices (in an integer table), and wants those...more Greetings OptoFans, I recently had someone ask me for some sample code to make use of a loop in OptoScript. In his application, he has several user choices (in an integer table), and wants those options to act like radio buttons. In other words, if one choice is selected, the others are de-selected. He originally solved this with multiple if statements but was looking for a loop option. Here’s his original code and my suggested loop. I’m hoping you Clever People Out There in OptoLand will have ...... <less Selecting a Solid state relay for a 1HP 120VAC motor Forum - Published: I have a customer with a 1HP 120VAC pump ùsing a smart device to time and control it. Another person has tried some generic 25A 250V and 40A 380V SSRs with all failure. One 25A unit faled-open, one...moreI have a customer with a 1HP 120VAC pump ùsing a smart device to time and control it. Another person has tried some generic 25A 250V and 40A 380V SSRs with all failure. One 25A unit faled-open, one failed-closed(shorted), and the 40A unit failed-closed. All had heat sinks with proper compound. I have assured this new customer that we can provide a reliable permanent solution, using an Opto22 product by an American company. What will be the best O22 SSR product to use for this application? And ...... <less Capture the edge of a state change Forum - Published: I develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a...moreI develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a comparison between LastState and the current value, if they are different I update the LastState variable to the current state and perform the required reaction. if ((InputPoint=1) and (LastState=0)) Then LastState=1; Perform whatever reaction should happen at the on edge elseif ((InputPoint=0) and (Last...... <less Groov Box Communication Error When Trying to read Static Tags Forum - Published: Getting this error when trying to access static tags in groov. How can I resolve this?... Getting this error when trying to access static tags in groov. How can I resolve this?... <less Long Epic Boot Time Forum - Published: First time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a...moreFirst time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a thin client as the HMI and I had to add an output that the strategy turns on to power the HMI when the EPIC was ready. The thin client boots much faster and can’t connect to the EPIC because it wasn’t ready. Now, though, the output comes on but the EPIC is still not ready so I have to add an additi...... <less FT232H to Flash Forum - Published: Hello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am...moreHello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am really trying to talk to the chip through a GROOV EPIC microcontroller through SSH PUTTY. Through this way, I can only get to trying to talk to the chip by git cloning to the site on putty through “git clone GitHub - optodeveloper/SSH-Demo” through that, I talked to the USB port through “/dev/ttyS...... <less What does "edge programmable" mean? Forum - Published: According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”....According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”.... <less Detect I/O Module Being Used Forum - Published: This may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module...moreThis may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module hardware currently connected to the Opto as possible. For analog cards I can retrieve the type/model of the module, whereas for digital it just says “Dig/None”. So I can’t get the model or even know if there is something connected in that slot. I saw an older post that seems to confirm that you just h...... <less MMP via Java? - old forum post Forum - Published: ashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the...moreashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the protocol for memory mapping using Java or if anyone knows where it can be found? I have started to duplicate it by going along with the c++ code from the toolkit but was wondering if there was an easier way to do it? Thanks Report 02-13-2009, 9:39 AM ben orchard Joined on 12-08-2004 Posts 33 Re: Java P...... <less Share data between EPICs (MQTT vs VPN)? Forum - Published: How do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very...moreHow do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very soon. For each facility, I have dashboard set up locally. These facilities, while they are remote, are connected to single VPN. We have HQ where our bosses sit. I plan to set up groov EPIC there to have a dashboard that will display data from remote facilities.... <less Read Entire Ignition Tag Arrays Using Loops & Dynamic Settings Forum - Published: Ignition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have...moreIgnition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have some part of each element’s name be the index. For example, you may have: strings/myAlarms/Alarm[0] , ../Alarm[1] , ../Alarm[2] , and ../Alarm[3] as an array of Alarm strings. While in this example they all exist in the one myAlarms folder, each element is an individual tag. So, if you want use Nod...... <less Mosquitto MQTT server in old cellphone Forum - Published: Hi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the...moreHi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the app Termux (linux terminal emulator) in order to run Mosquitto in the device, the PR1 nodered receives the data with no issues and I have performed intense testing and integrated with several devices. It works perfectly even with heavy loads and the built in battery gives me a lot of flexibility no...... <less « PreviousPage 2 of 6Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Hide Title bar in Groov view Forum - Published: Is there a way to Hide the title bar from certain users?...Is there a way to Hide the title bar from certain users?... <less SNAP-ODC-32-SRC to SNAP-UDC-HDB Ribbon Cable Alternative Forum - Published: My goal is to have the SNAP-UDC-HDB near the SNAP-ODC-32-SRC module, within 6" -12" inside the same electrical enclosure. Opto 22 sells the cables at 6ft lengths, this works great when you have the PAC...moreMy goal is to have the SNAP-UDC-HDB near the SNAP-ODC-32-SRC module, within 6" -12" inside the same electrical enclosure. Opto 22 sells the cables at 6ft lengths, this works great when you have the PAC Rack separated from the SNAP-UDC-HDB at that distance. I researched for an alternate method of connecting them. Turns out that a 40 pin hard drive cable works! I purchased 12" length cables for $6 each. Note the cable must have pin 20 open, not filled in for it to work. Attached is how I connected...... <less Trane Chiller UC800 Controller Inerface Forum - Published: Just seeing if anyone out there has successfully interfaced a trace chiller UC800 controller to Opto via either Modbus or BACNET?? Currently having a few issues with both. Modbus im using a mgate modbus...moreJust seeing if anyone out there has successfully interfaced a trace chiller UC800 controller to Opto via either Modbus or BACNET?? Currently having a few issues with both. Modbus im using a mgate modbus gateway to convert the Modbus RTU to Modbus TCP/IP. Im using modbus poll to check the data coming out and all that it keeps coming back with illegal packet length. Bacnet I can see the UC800 and can read the object names but cant read any of the actual values. I can see both object names and valu...... <less RIO Node-Red Listening on non-standard port Forum - Published: Hello, I have my device IO figured out on a RIO. Next step is getting TCP listener to work. The flow I am working on needs to listen on a specific port for a message. I am using ETH-0. The application...moreHello, I have my device IO figured out on a RIO. Next step is getting TCP listener to work. The flow I am working on needs to listen on a specific port for a message. I am using ETH-0. The application residing on another machine will simple open a connection to the RIO and send messages to it for the RIO to take actions. When I deploy the TCP listener to listen to a port number less than 1024 I get a permission denied. I attempted to add a firewall rule on the RIO to for the subject port and ...... <less OptoMMP Tool kit? Forum - Published: Is this version specific? i.e. Can the latest version be used with Pac Control 8.5? Which version has ActiveX controls that supports Legacy VisualBasic applications (VB 6.0)? Thanks....Is this version specific? i.e. Can the latest version be used with Pac Control 8.5? Which version has ActiveX controls that supports Legacy VisualBasic applications (VB 6.0)? Thanks.... <less Groov EPIC-PR1 - Restful API Forum - Published: Hey Guys, I might be missing it, but is there no restful api for the EPIC-PR1 like the snap-pac-r1/r2? I know that we can build a similar function like it through node-red, but wouldn’t it make sense...moreHey Guys, I might be missing it, but is there no restful api for the EPIC-PR1 like the snap-pac-r1/r2? I know that we can build a similar function like it through node-red, but wouldn’t it make sense just to have it baked in as well? Saves a lot of work and testing. I am using a mixture of PR1 & R2’s, mainly because I need reliable serial comms for modbus RTU. Once the serial module is ready for the PR1, I will be swapping a lot and changing future builds. It would be nice to use my curren...... <less PAC Project Versions Forum - Published: Almost 95% of my projects were created with PAC Project version R9.6003-86. On one of my PCs, I must have used a more recent version maybe R9.6004-109, R9.6005-125 or R9.6006-131. First off, how can I...moreAlmost 95% of my projects were created with PAC Project version R9.6003-86. On one of my PCs, I must have used a more recent version maybe R9.6004-109, R9.6005-125 or R9.6006-131. First off, how can I tell which PAC Project this PC is running. (sure, I can see Control is R9.6e, Display is R9.6F Build 0092 and SoftPAC is v.R9.6a, but what Project version installed those?) Secondly, can I reinstall R9.6003-86 on this same PC and both versions will work (maybe in a different location on my PC)? L...... <less Max number of trends in a project? Forum - Published: Is there a maximum number of trends in a project? I keep trying to add one and the trend gadget just crashes/never loads in ‘View’. I have tried interactive and classic. trend_crash.png1068×329 21.3...moreIs there a maximum number of trends in a project? I keep trying to add one and the trend gadget just crashes/never loads in ‘View’. I have tried interactive and classic. trend_crash.png1068×329 21.3 KB The values to the left are the same values used in the trend.... <less Which groov EPIC Module for humidity sensor? Forum - Published: Hi Ma’am/Sir, May I ask if what module can read a humidity sensor? I have already created in our Data Center a Temperature Monitoring and used the GRV-ITMI-8 module. Thanks in advance. Best Regards, Jay...Hi Ma’am/Sir, May I ask if what module can read a humidity sensor? I have already created in our Data Center a Temperature Monitoring and used the GRV-ITMI-8 module. Thanks in advance. Best Regards, Jay... <less SNAP-OMR6 vs SNAP-ODC5R. Mechanical relay ouput modules Forum - Published: It still surprises me how many people work with Opto 22 hardware and software and yet are not signed up to OptoNews and so miss out on hearing all the cool stuff that happens in the world of Opto 22...moreIt still surprises me how many people work with Opto 22 hardware and software and yet are not signed up to OptoNews and so miss out on hearing all the cool stuff that happens in the world of Opto 22… Another topic for another day perhaps, right now I just want to answer a question about our new digital output modules which got announced in[URL=“http://www.opto22.com/site/optonews/2011/optonews_08312011.aspx”] last week’s OptoNews. SNAP-OMR6. 4 channels of 6 amp mechanical relay goodness, more th...... <less A pulse signal generated by the Holzer sensor Forum - Published: Excuse me, a pulse signal generated by the Holzer sensor, can use the IDC5 count? If not, what kind of module is used? Thank you...Excuse me, a pulse signal generated by the Holzer sensor, can use the IDC5 count? If not, what kind of module is used? Thank you... <less Fonts rendered at different sizes for different controls Forum - Published: I’ve come across a minor inconsistency with the size text is rendered for the Button control and the Text object. In typical WinForms applications these fonts would be displayed the same size if they...moreI’ve come across a minor inconsistency with the size text is rendered for the Button control and the Text object. In typical WinForms applications these fonts would be displayed the same size if they are configured to the same font size. I’ve attached a screen shot that illustrates the difference, both of these controls are set to: MS Sans Serif Bold 20pt Is this a known issue? different font sizes on controls.png818×506 8.23 KB Regards, Steve... <less Radio button-like behavior Forum - Published: Greetings OptoFans, I recently had someone ask me for some sample code to make use of a loop in OptoScript. In his application, he has several user choices (in an integer table), and wants those...more Greetings OptoFans, I recently had someone ask me for some sample code to make use of a loop in OptoScript. In his application, he has several user choices (in an integer table), and wants those options to act like radio buttons. In other words, if one choice is selected, the others are de-selected. He originally solved this with multiple if statements but was looking for a loop option. Here’s his original code and my suggested loop. I’m hoping you Clever People Out There in OptoLand will have ...... <less Selecting a Solid state relay for a 1HP 120VAC motor Forum - Published: I have a customer with a 1HP 120VAC pump ùsing a smart device to time and control it. Another person has tried some generic 25A 250V and 40A 380V SSRs with all failure. One 25A unit faled-open, one...moreI have a customer with a 1HP 120VAC pump ùsing a smart device to time and control it. Another person has tried some generic 25A 250V and 40A 380V SSRs with all failure. One 25A unit faled-open, one failed-closed(shorted), and the 40A unit failed-closed. All had heat sinks with proper compound. I have assured this new customer that we can provide a reliable permanent solution, using an Opto22 product by an American company. What will be the best O22 SSR product to use for this application? And ...... <less Capture the edge of a state change Forum - Published: I develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a...moreI develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a comparison between LastState and the current value, if they are different I update the LastState variable to the current state and perform the required reaction. if ((InputPoint=1) and (LastState=0)) Then LastState=1; Perform whatever reaction should happen at the on edge elseif ((InputPoint=0) and (Last...... <less Groov Box Communication Error When Trying to read Static Tags Forum - Published: Getting this error when trying to access static tags in groov. How can I resolve this?... Getting this error when trying to access static tags in groov. How can I resolve this?... <less Long Epic Boot Time Forum - Published: First time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a...moreFirst time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a thin client as the HMI and I had to add an output that the strategy turns on to power the HMI when the EPIC was ready. The thin client boots much faster and can’t connect to the EPIC because it wasn’t ready. Now, though, the output comes on but the EPIC is still not ready so I have to add an additi...... <less FT232H to Flash Forum - Published: Hello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am...moreHello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am really trying to talk to the chip through a GROOV EPIC microcontroller through SSH PUTTY. Through this way, I can only get to trying to talk to the chip by git cloning to the site on putty through “git clone GitHub - optodeveloper/SSH-Demo” through that, I talked to the USB port through “/dev/ttyS...... <less What does "edge programmable" mean? Forum - Published: According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”....According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”.... <less Detect I/O Module Being Used Forum - Published: This may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module...moreThis may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module hardware currently connected to the Opto as possible. For analog cards I can retrieve the type/model of the module, whereas for digital it just says “Dig/None”. So I can’t get the model or even know if there is something connected in that slot. I saw an older post that seems to confirm that you just h...... <less MMP via Java? - old forum post Forum - Published: ashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the...moreashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the protocol for memory mapping using Java or if anyone knows where it can be found? I have started to duplicate it by going along with the c++ code from the toolkit but was wondering if there was an easier way to do it? Thanks Report 02-13-2009, 9:39 AM ben orchard Joined on 12-08-2004 Posts 33 Re: Java P...... <less Share data between EPICs (MQTT vs VPN)? Forum - Published: How do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very...moreHow do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very soon. For each facility, I have dashboard set up locally. These facilities, while they are remote, are connected to single VPN. We have HQ where our bosses sit. I plan to set up groov EPIC there to have a dashboard that will display data from remote facilities.... <less Read Entire Ignition Tag Arrays Using Loops & Dynamic Settings Forum - Published: Ignition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have...moreIgnition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have some part of each element’s name be the index. For example, you may have: strings/myAlarms/Alarm[0] , ../Alarm[1] , ../Alarm[2] , and ../Alarm[3] as an array of Alarm strings. While in this example they all exist in the one myAlarms folder, each element is an individual tag. So, if you want use Nod...... <less Mosquitto MQTT server in old cellphone Forum - Published: Hi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the...moreHi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the app Termux (linux terminal emulator) in order to run Mosquitto in the device, the PR1 nodered receives the data with no issues and I have performed intense testing and integrated with several devices. It works perfectly even with heavy loads and the built in battery gives me a lot of flexibility no...... <less « PreviousPage 2 of 6Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
SNAP-ODC-32-SRC to SNAP-UDC-HDB Ribbon Cable Alternative Forum - Published: My goal is to have the SNAP-UDC-HDB near the SNAP-ODC-32-SRC module, within 6" -12" inside the same electrical enclosure. Opto 22 sells the cables at 6ft lengths, this works great when you have the PAC...moreMy goal is to have the SNAP-UDC-HDB near the SNAP-ODC-32-SRC module, within 6" -12" inside the same electrical enclosure. Opto 22 sells the cables at 6ft lengths, this works great when you have the PAC Rack separated from the SNAP-UDC-HDB at that distance. I researched for an alternate method of connecting them. Turns out that a 40 pin hard drive cable works! I purchased 12" length cables for $6 each. Note the cable must have pin 20 open, not filled in for it to work. Attached is how I connected...... <less Trane Chiller UC800 Controller Inerface Forum - Published: Just seeing if anyone out there has successfully interfaced a trace chiller UC800 controller to Opto via either Modbus or BACNET?? Currently having a few issues with both. Modbus im using a mgate modbus...moreJust seeing if anyone out there has successfully interfaced a trace chiller UC800 controller to Opto via either Modbus or BACNET?? Currently having a few issues with both. Modbus im using a mgate modbus gateway to convert the Modbus RTU to Modbus TCP/IP. Im using modbus poll to check the data coming out and all that it keeps coming back with illegal packet length. Bacnet I can see the UC800 and can read the object names but cant read any of the actual values. I can see both object names and valu...... <less RIO Node-Red Listening on non-standard port Forum - Published: Hello, I have my device IO figured out on a RIO. Next step is getting TCP listener to work. The flow I am working on needs to listen on a specific port for a message. I am using ETH-0. The application...moreHello, I have my device IO figured out on a RIO. Next step is getting TCP listener to work. The flow I am working on needs to listen on a specific port for a message. I am using ETH-0. The application residing on another machine will simple open a connection to the RIO and send messages to it for the RIO to take actions. When I deploy the TCP listener to listen to a port number less than 1024 I get a permission denied. I attempted to add a firewall rule on the RIO to for the subject port and ...... <less OptoMMP Tool kit? Forum - Published: Is this version specific? i.e. Can the latest version be used with Pac Control 8.5? Which version has ActiveX controls that supports Legacy VisualBasic applications (VB 6.0)? Thanks....Is this version specific? i.e. Can the latest version be used with Pac Control 8.5? Which version has ActiveX controls that supports Legacy VisualBasic applications (VB 6.0)? Thanks.... <less Groov EPIC-PR1 - Restful API Forum - Published: Hey Guys, I might be missing it, but is there no restful api for the EPIC-PR1 like the snap-pac-r1/r2? I know that we can build a similar function like it through node-red, but wouldn’t it make sense...moreHey Guys, I might be missing it, but is there no restful api for the EPIC-PR1 like the snap-pac-r1/r2? I know that we can build a similar function like it through node-red, but wouldn’t it make sense just to have it baked in as well? Saves a lot of work and testing. I am using a mixture of PR1 & R2’s, mainly because I need reliable serial comms for modbus RTU. Once the serial module is ready for the PR1, I will be swapping a lot and changing future builds. It would be nice to use my curren...... <less PAC Project Versions Forum - Published: Almost 95% of my projects were created with PAC Project version R9.6003-86. On one of my PCs, I must have used a more recent version maybe R9.6004-109, R9.6005-125 or R9.6006-131. First off, how can I...moreAlmost 95% of my projects were created with PAC Project version R9.6003-86. On one of my PCs, I must have used a more recent version maybe R9.6004-109, R9.6005-125 or R9.6006-131. First off, how can I tell which PAC Project this PC is running. (sure, I can see Control is R9.6e, Display is R9.6F Build 0092 and SoftPAC is v.R9.6a, but what Project version installed those?) Secondly, can I reinstall R9.6003-86 on this same PC and both versions will work (maybe in a different location on my PC)? L...... <less Max number of trends in a project? Forum - Published: Is there a maximum number of trends in a project? I keep trying to add one and the trend gadget just crashes/never loads in ‘View’. I have tried interactive and classic. trend_crash.png1068×329 21.3...moreIs there a maximum number of trends in a project? I keep trying to add one and the trend gadget just crashes/never loads in ‘View’. I have tried interactive and classic. trend_crash.png1068×329 21.3 KB The values to the left are the same values used in the trend.... <less Which groov EPIC Module for humidity sensor? Forum - Published: Hi Ma’am/Sir, May I ask if what module can read a humidity sensor? I have already created in our Data Center a Temperature Monitoring and used the GRV-ITMI-8 module. Thanks in advance. Best Regards, Jay...Hi Ma’am/Sir, May I ask if what module can read a humidity sensor? I have already created in our Data Center a Temperature Monitoring and used the GRV-ITMI-8 module. Thanks in advance. Best Regards, Jay... <less SNAP-OMR6 vs SNAP-ODC5R. Mechanical relay ouput modules Forum - Published: It still surprises me how many people work with Opto 22 hardware and software and yet are not signed up to OptoNews and so miss out on hearing all the cool stuff that happens in the world of Opto 22...moreIt still surprises me how many people work with Opto 22 hardware and software and yet are not signed up to OptoNews and so miss out on hearing all the cool stuff that happens in the world of Opto 22… Another topic for another day perhaps, right now I just want to answer a question about our new digital output modules which got announced in[URL=“http://www.opto22.com/site/optonews/2011/optonews_08312011.aspx”] last week’s OptoNews. SNAP-OMR6. 4 channels of 6 amp mechanical relay goodness, more th...... <less A pulse signal generated by the Holzer sensor Forum - Published: Excuse me, a pulse signal generated by the Holzer sensor, can use the IDC5 count? If not, what kind of module is used? Thank you...Excuse me, a pulse signal generated by the Holzer sensor, can use the IDC5 count? If not, what kind of module is used? Thank you... <less Fonts rendered at different sizes for different controls Forum - Published: I’ve come across a minor inconsistency with the size text is rendered for the Button control and the Text object. In typical WinForms applications these fonts would be displayed the same size if they...moreI’ve come across a minor inconsistency with the size text is rendered for the Button control and the Text object. In typical WinForms applications these fonts would be displayed the same size if they are configured to the same font size. I’ve attached a screen shot that illustrates the difference, both of these controls are set to: MS Sans Serif Bold 20pt Is this a known issue? different font sizes on controls.png818×506 8.23 KB Regards, Steve... <less Radio button-like behavior Forum - Published: Greetings OptoFans, I recently had someone ask me for some sample code to make use of a loop in OptoScript. In his application, he has several user choices (in an integer table), and wants those...more Greetings OptoFans, I recently had someone ask me for some sample code to make use of a loop in OptoScript. In his application, he has several user choices (in an integer table), and wants those options to act like radio buttons. In other words, if one choice is selected, the others are de-selected. He originally solved this with multiple if statements but was looking for a loop option. Here’s his original code and my suggested loop. I’m hoping you Clever People Out There in OptoLand will have ...... <less Selecting a Solid state relay for a 1HP 120VAC motor Forum - Published: I have a customer with a 1HP 120VAC pump ùsing a smart device to time and control it. Another person has tried some generic 25A 250V and 40A 380V SSRs with all failure. One 25A unit faled-open, one...moreI have a customer with a 1HP 120VAC pump ùsing a smart device to time and control it. Another person has tried some generic 25A 250V and 40A 380V SSRs with all failure. One 25A unit faled-open, one failed-closed(shorted), and the 40A unit failed-closed. All had heat sinks with proper compound. I have assured this new customer that we can provide a reliable permanent solution, using an Opto22 product by an American company. What will be the best O22 SSR product to use for this application? And ...... <less Capture the edge of a state change Forum - Published: I develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a...moreI develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a comparison between LastState and the current value, if they are different I update the LastState variable to the current state and perform the required reaction. if ((InputPoint=1) and (LastState=0)) Then LastState=1; Perform whatever reaction should happen at the on edge elseif ((InputPoint=0) and (Last...... <less Groov Box Communication Error When Trying to read Static Tags Forum - Published: Getting this error when trying to access static tags in groov. How can I resolve this?... Getting this error when trying to access static tags in groov. How can I resolve this?... <less Long Epic Boot Time Forum - Published: First time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a...moreFirst time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a thin client as the HMI and I had to add an output that the strategy turns on to power the HMI when the EPIC was ready. The thin client boots much faster and can’t connect to the EPIC because it wasn’t ready. Now, though, the output comes on but the EPIC is still not ready so I have to add an additi...... <less FT232H to Flash Forum - Published: Hello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am...moreHello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am really trying to talk to the chip through a GROOV EPIC microcontroller through SSH PUTTY. Through this way, I can only get to trying to talk to the chip by git cloning to the site on putty through “git clone GitHub - optodeveloper/SSH-Demo” through that, I talked to the USB port through “/dev/ttyS...... <less What does "edge programmable" mean? Forum - Published: According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”....According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”.... <less Detect I/O Module Being Used Forum - Published: This may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module...moreThis may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module hardware currently connected to the Opto as possible. For analog cards I can retrieve the type/model of the module, whereas for digital it just says “Dig/None”. So I can’t get the model or even know if there is something connected in that slot. I saw an older post that seems to confirm that you just h...... <less MMP via Java? - old forum post Forum - Published: ashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the...moreashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the protocol for memory mapping using Java or if anyone knows where it can be found? I have started to duplicate it by going along with the c++ code from the toolkit but was wondering if there was an easier way to do it? Thanks Report 02-13-2009, 9:39 AM ben orchard Joined on 12-08-2004 Posts 33 Re: Java P...... <less Share data between EPICs (MQTT vs VPN)? Forum - Published: How do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very...moreHow do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very soon. For each facility, I have dashboard set up locally. These facilities, while they are remote, are connected to single VPN. We have HQ where our bosses sit. I plan to set up groov EPIC there to have a dashboard that will display data from remote facilities.... <less Read Entire Ignition Tag Arrays Using Loops & Dynamic Settings Forum - Published: Ignition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have...moreIgnition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have some part of each element’s name be the index. For example, you may have: strings/myAlarms/Alarm[0] , ../Alarm[1] , ../Alarm[2] , and ../Alarm[3] as an array of Alarm strings. While in this example they all exist in the one myAlarms folder, each element is an individual tag. So, if you want use Nod...... <less Mosquitto MQTT server in old cellphone Forum - Published: Hi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the...moreHi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the app Termux (linux terminal emulator) in order to run Mosquitto in the device, the PR1 nodered receives the data with no issues and I have performed intense testing and integrated with several devices. It works perfectly even with heavy loads and the built in battery gives me a lot of flexibility no...... <less « PreviousPage 2 of 6Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Trane Chiller UC800 Controller Inerface Forum - Published: Just seeing if anyone out there has successfully interfaced a trace chiller UC800 controller to Opto via either Modbus or BACNET?? Currently having a few issues with both. Modbus im using a mgate modbus...moreJust seeing if anyone out there has successfully interfaced a trace chiller UC800 controller to Opto via either Modbus or BACNET?? Currently having a few issues with both. Modbus im using a mgate modbus gateway to convert the Modbus RTU to Modbus TCP/IP. Im using modbus poll to check the data coming out and all that it keeps coming back with illegal packet length. Bacnet I can see the UC800 and can read the object names but cant read any of the actual values. I can see both object names and valu...... <less RIO Node-Red Listening on non-standard port Forum - Published: Hello, I have my device IO figured out on a RIO. Next step is getting TCP listener to work. The flow I am working on needs to listen on a specific port for a message. I am using ETH-0. The application...moreHello, I have my device IO figured out on a RIO. Next step is getting TCP listener to work. The flow I am working on needs to listen on a specific port for a message. I am using ETH-0. The application residing on another machine will simple open a connection to the RIO and send messages to it for the RIO to take actions. When I deploy the TCP listener to listen to a port number less than 1024 I get a permission denied. I attempted to add a firewall rule on the RIO to for the subject port and ...... <less OptoMMP Tool kit? Forum - Published: Is this version specific? i.e. Can the latest version be used with Pac Control 8.5? Which version has ActiveX controls that supports Legacy VisualBasic applications (VB 6.0)? Thanks....Is this version specific? i.e. Can the latest version be used with Pac Control 8.5? Which version has ActiveX controls that supports Legacy VisualBasic applications (VB 6.0)? Thanks.... <less Groov EPIC-PR1 - Restful API Forum - Published: Hey Guys, I might be missing it, but is there no restful api for the EPIC-PR1 like the snap-pac-r1/r2? I know that we can build a similar function like it through node-red, but wouldn’t it make sense...moreHey Guys, I might be missing it, but is there no restful api for the EPIC-PR1 like the snap-pac-r1/r2? I know that we can build a similar function like it through node-red, but wouldn’t it make sense just to have it baked in as well? Saves a lot of work and testing. I am using a mixture of PR1 & R2’s, mainly because I need reliable serial comms for modbus RTU. Once the serial module is ready for the PR1, I will be swapping a lot and changing future builds. It would be nice to use my curren...... <less PAC Project Versions Forum - Published: Almost 95% of my projects were created with PAC Project version R9.6003-86. On one of my PCs, I must have used a more recent version maybe R9.6004-109, R9.6005-125 or R9.6006-131. First off, how can I...moreAlmost 95% of my projects were created with PAC Project version R9.6003-86. On one of my PCs, I must have used a more recent version maybe R9.6004-109, R9.6005-125 or R9.6006-131. First off, how can I tell which PAC Project this PC is running. (sure, I can see Control is R9.6e, Display is R9.6F Build 0092 and SoftPAC is v.R9.6a, but what Project version installed those?) Secondly, can I reinstall R9.6003-86 on this same PC and both versions will work (maybe in a different location on my PC)? L...... <less Max number of trends in a project? Forum - Published: Is there a maximum number of trends in a project? I keep trying to add one and the trend gadget just crashes/never loads in ‘View’. I have tried interactive and classic. trend_crash.png1068×329 21.3...moreIs there a maximum number of trends in a project? I keep trying to add one and the trend gadget just crashes/never loads in ‘View’. I have tried interactive and classic. trend_crash.png1068×329 21.3 KB The values to the left are the same values used in the trend.... <less Which groov EPIC Module for humidity sensor? Forum - Published: Hi Ma’am/Sir, May I ask if what module can read a humidity sensor? I have already created in our Data Center a Temperature Monitoring and used the GRV-ITMI-8 module. Thanks in advance. Best Regards, Jay...Hi Ma’am/Sir, May I ask if what module can read a humidity sensor? I have already created in our Data Center a Temperature Monitoring and used the GRV-ITMI-8 module. Thanks in advance. Best Regards, Jay... <less SNAP-OMR6 vs SNAP-ODC5R. Mechanical relay ouput modules Forum - Published: It still surprises me how many people work with Opto 22 hardware and software and yet are not signed up to OptoNews and so miss out on hearing all the cool stuff that happens in the world of Opto 22...moreIt still surprises me how many people work with Opto 22 hardware and software and yet are not signed up to OptoNews and so miss out on hearing all the cool stuff that happens in the world of Opto 22… Another topic for another day perhaps, right now I just want to answer a question about our new digital output modules which got announced in[URL=“http://www.opto22.com/site/optonews/2011/optonews_08312011.aspx”] last week’s OptoNews. SNAP-OMR6. 4 channels of 6 amp mechanical relay goodness, more th...... <less A pulse signal generated by the Holzer sensor Forum - Published: Excuse me, a pulse signal generated by the Holzer sensor, can use the IDC5 count? If not, what kind of module is used? Thank you...Excuse me, a pulse signal generated by the Holzer sensor, can use the IDC5 count? If not, what kind of module is used? Thank you... <less Fonts rendered at different sizes for different controls Forum - Published: I’ve come across a minor inconsistency with the size text is rendered for the Button control and the Text object. In typical WinForms applications these fonts would be displayed the same size if they...moreI’ve come across a minor inconsistency with the size text is rendered for the Button control and the Text object. In typical WinForms applications these fonts would be displayed the same size if they are configured to the same font size. I’ve attached a screen shot that illustrates the difference, both of these controls are set to: MS Sans Serif Bold 20pt Is this a known issue? different font sizes on controls.png818×506 8.23 KB Regards, Steve... <less Radio button-like behavior Forum - Published: Greetings OptoFans, I recently had someone ask me for some sample code to make use of a loop in OptoScript. In his application, he has several user choices (in an integer table), and wants those...more Greetings OptoFans, I recently had someone ask me for some sample code to make use of a loop in OptoScript. In his application, he has several user choices (in an integer table), and wants those options to act like radio buttons. In other words, if one choice is selected, the others are de-selected. He originally solved this with multiple if statements but was looking for a loop option. Here’s his original code and my suggested loop. I’m hoping you Clever People Out There in OptoLand will have ...... <less Selecting a Solid state relay for a 1HP 120VAC motor Forum - Published: I have a customer with a 1HP 120VAC pump ùsing a smart device to time and control it. Another person has tried some generic 25A 250V and 40A 380V SSRs with all failure. One 25A unit faled-open, one...moreI have a customer with a 1HP 120VAC pump ùsing a smart device to time and control it. Another person has tried some generic 25A 250V and 40A 380V SSRs with all failure. One 25A unit faled-open, one failed-closed(shorted), and the 40A unit failed-closed. All had heat sinks with proper compound. I have assured this new customer that we can provide a reliable permanent solution, using an Opto22 product by an American company. What will be the best O22 SSR product to use for this application? And ...... <less Capture the edge of a state change Forum - Published: I develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a...moreI develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a comparison between LastState and the current value, if they are different I update the LastState variable to the current state and perform the required reaction. if ((InputPoint=1) and (LastState=0)) Then LastState=1; Perform whatever reaction should happen at the on edge elseif ((InputPoint=0) and (Last...... <less Groov Box Communication Error When Trying to read Static Tags Forum - Published: Getting this error when trying to access static tags in groov. How can I resolve this?... Getting this error when trying to access static tags in groov. How can I resolve this?... <less Long Epic Boot Time Forum - Published: First time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a...moreFirst time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a thin client as the HMI and I had to add an output that the strategy turns on to power the HMI when the EPIC was ready. The thin client boots much faster and can’t connect to the EPIC because it wasn’t ready. Now, though, the output comes on but the EPIC is still not ready so I have to add an additi...... <less FT232H to Flash Forum - Published: Hello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am...moreHello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am really trying to talk to the chip through a GROOV EPIC microcontroller through SSH PUTTY. Through this way, I can only get to trying to talk to the chip by git cloning to the site on putty through “git clone GitHub - optodeveloper/SSH-Demo” through that, I talked to the USB port through “/dev/ttyS...... <less What does "edge programmable" mean? Forum - Published: According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”....According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”.... <less Detect I/O Module Being Used Forum - Published: This may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module...moreThis may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module hardware currently connected to the Opto as possible. For analog cards I can retrieve the type/model of the module, whereas for digital it just says “Dig/None”. So I can’t get the model or even know if there is something connected in that slot. I saw an older post that seems to confirm that you just h...... <less MMP via Java? - old forum post Forum - Published: ashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the...moreashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the protocol for memory mapping using Java or if anyone knows where it can be found? I have started to duplicate it by going along with the c++ code from the toolkit but was wondering if there was an easier way to do it? Thanks Report 02-13-2009, 9:39 AM ben orchard Joined on 12-08-2004 Posts 33 Re: Java P...... <less Share data between EPICs (MQTT vs VPN)? Forum - Published: How do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very...moreHow do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very soon. For each facility, I have dashboard set up locally. These facilities, while they are remote, are connected to single VPN. We have HQ where our bosses sit. I plan to set up groov EPIC there to have a dashboard that will display data from remote facilities.... <less Read Entire Ignition Tag Arrays Using Loops & Dynamic Settings Forum - Published: Ignition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have...moreIgnition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have some part of each element’s name be the index. For example, you may have: strings/myAlarms/Alarm[0] , ../Alarm[1] , ../Alarm[2] , and ../Alarm[3] as an array of Alarm strings. While in this example they all exist in the one myAlarms folder, each element is an individual tag. So, if you want use Nod...... <less Mosquitto MQTT server in old cellphone Forum - Published: Hi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the...moreHi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the app Termux (linux terminal emulator) in order to run Mosquitto in the device, the PR1 nodered receives the data with no issues and I have performed intense testing and integrated with several devices. It works perfectly even with heavy loads and the built in battery gives me a lot of flexibility no...... <less « PreviousPage 2 of 6Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
RIO Node-Red Listening on non-standard port Forum - Published: Hello, I have my device IO figured out on a RIO. Next step is getting TCP listener to work. The flow I am working on needs to listen on a specific port for a message. I am using ETH-0. The application...moreHello, I have my device IO figured out on a RIO. Next step is getting TCP listener to work. The flow I am working on needs to listen on a specific port for a message. I am using ETH-0. The application residing on another machine will simple open a connection to the RIO and send messages to it for the RIO to take actions. When I deploy the TCP listener to listen to a port number less than 1024 I get a permission denied. I attempted to add a firewall rule on the RIO to for the subject port and ...... <less OptoMMP Tool kit? Forum - Published: Is this version specific? i.e. Can the latest version be used with Pac Control 8.5? Which version has ActiveX controls that supports Legacy VisualBasic applications (VB 6.0)? Thanks....Is this version specific? i.e. Can the latest version be used with Pac Control 8.5? Which version has ActiveX controls that supports Legacy VisualBasic applications (VB 6.0)? Thanks.... <less Groov EPIC-PR1 - Restful API Forum - Published: Hey Guys, I might be missing it, but is there no restful api for the EPIC-PR1 like the snap-pac-r1/r2? I know that we can build a similar function like it through node-red, but wouldn’t it make sense...moreHey Guys, I might be missing it, but is there no restful api for the EPIC-PR1 like the snap-pac-r1/r2? I know that we can build a similar function like it through node-red, but wouldn’t it make sense just to have it baked in as well? Saves a lot of work and testing. I am using a mixture of PR1 & R2’s, mainly because I need reliable serial comms for modbus RTU. Once the serial module is ready for the PR1, I will be swapping a lot and changing future builds. It would be nice to use my curren...... <less PAC Project Versions Forum - Published: Almost 95% of my projects were created with PAC Project version R9.6003-86. On one of my PCs, I must have used a more recent version maybe R9.6004-109, R9.6005-125 or R9.6006-131. First off, how can I...moreAlmost 95% of my projects were created with PAC Project version R9.6003-86. On one of my PCs, I must have used a more recent version maybe R9.6004-109, R9.6005-125 or R9.6006-131. First off, how can I tell which PAC Project this PC is running. (sure, I can see Control is R9.6e, Display is R9.6F Build 0092 and SoftPAC is v.R9.6a, but what Project version installed those?) Secondly, can I reinstall R9.6003-86 on this same PC and both versions will work (maybe in a different location on my PC)? L...... <less Max number of trends in a project? Forum - Published: Is there a maximum number of trends in a project? I keep trying to add one and the trend gadget just crashes/never loads in ‘View’. I have tried interactive and classic. trend_crash.png1068×329 21.3...moreIs there a maximum number of trends in a project? I keep trying to add one and the trend gadget just crashes/never loads in ‘View’. I have tried interactive and classic. trend_crash.png1068×329 21.3 KB The values to the left are the same values used in the trend.... <less Which groov EPIC Module for humidity sensor? Forum - Published: Hi Ma’am/Sir, May I ask if what module can read a humidity sensor? I have already created in our Data Center a Temperature Monitoring and used the GRV-ITMI-8 module. Thanks in advance. Best Regards, Jay...Hi Ma’am/Sir, May I ask if what module can read a humidity sensor? I have already created in our Data Center a Temperature Monitoring and used the GRV-ITMI-8 module. Thanks in advance. Best Regards, Jay... <less SNAP-OMR6 vs SNAP-ODC5R. Mechanical relay ouput modules Forum - Published: It still surprises me how many people work with Opto 22 hardware and software and yet are not signed up to OptoNews and so miss out on hearing all the cool stuff that happens in the world of Opto 22...moreIt still surprises me how many people work with Opto 22 hardware and software and yet are not signed up to OptoNews and so miss out on hearing all the cool stuff that happens in the world of Opto 22… Another topic for another day perhaps, right now I just want to answer a question about our new digital output modules which got announced in[URL=“http://www.opto22.com/site/optonews/2011/optonews_08312011.aspx”] last week’s OptoNews. SNAP-OMR6. 4 channels of 6 amp mechanical relay goodness, more th...... <less A pulse signal generated by the Holzer sensor Forum - Published: Excuse me, a pulse signal generated by the Holzer sensor, can use the IDC5 count? If not, what kind of module is used? Thank you...Excuse me, a pulse signal generated by the Holzer sensor, can use the IDC5 count? If not, what kind of module is used? Thank you... <less Fonts rendered at different sizes for different controls Forum - Published: I’ve come across a minor inconsistency with the size text is rendered for the Button control and the Text object. In typical WinForms applications these fonts would be displayed the same size if they...moreI’ve come across a minor inconsistency with the size text is rendered for the Button control and the Text object. In typical WinForms applications these fonts would be displayed the same size if they are configured to the same font size. I’ve attached a screen shot that illustrates the difference, both of these controls are set to: MS Sans Serif Bold 20pt Is this a known issue? different font sizes on controls.png818×506 8.23 KB Regards, Steve... <less Radio button-like behavior Forum - Published: Greetings OptoFans, I recently had someone ask me for some sample code to make use of a loop in OptoScript. In his application, he has several user choices (in an integer table), and wants those...more Greetings OptoFans, I recently had someone ask me for some sample code to make use of a loop in OptoScript. In his application, he has several user choices (in an integer table), and wants those options to act like radio buttons. In other words, if one choice is selected, the others are de-selected. He originally solved this with multiple if statements but was looking for a loop option. Here’s his original code and my suggested loop. I’m hoping you Clever People Out There in OptoLand will have ...... <less Selecting a Solid state relay for a 1HP 120VAC motor Forum - Published: I have a customer with a 1HP 120VAC pump ùsing a smart device to time and control it. Another person has tried some generic 25A 250V and 40A 380V SSRs with all failure. One 25A unit faled-open, one...moreI have a customer with a 1HP 120VAC pump ùsing a smart device to time and control it. Another person has tried some generic 25A 250V and 40A 380V SSRs with all failure. One 25A unit faled-open, one failed-closed(shorted), and the 40A unit failed-closed. All had heat sinks with proper compound. I have assured this new customer that we can provide a reliable permanent solution, using an Opto22 product by an American company. What will be the best O22 SSR product to use for this application? And ...... <less Capture the edge of a state change Forum - Published: I develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a...moreI develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a comparison between LastState and the current value, if they are different I update the LastState variable to the current state and perform the required reaction. if ((InputPoint=1) and (LastState=0)) Then LastState=1; Perform whatever reaction should happen at the on edge elseif ((InputPoint=0) and (Last...... <less Groov Box Communication Error When Trying to read Static Tags Forum - Published: Getting this error when trying to access static tags in groov. How can I resolve this?... Getting this error when trying to access static tags in groov. How can I resolve this?... <less Long Epic Boot Time Forum - Published: First time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a...moreFirst time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a thin client as the HMI and I had to add an output that the strategy turns on to power the HMI when the EPIC was ready. The thin client boots much faster and can’t connect to the EPIC because it wasn’t ready. Now, though, the output comes on but the EPIC is still not ready so I have to add an additi...... <less FT232H to Flash Forum - Published: Hello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am...moreHello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am really trying to talk to the chip through a GROOV EPIC microcontroller through SSH PUTTY. Through this way, I can only get to trying to talk to the chip by git cloning to the site on putty through “git clone GitHub - optodeveloper/SSH-Demo” through that, I talked to the USB port through “/dev/ttyS...... <less What does "edge programmable" mean? Forum - Published: According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”....According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”.... <less Detect I/O Module Being Used Forum - Published: This may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module...moreThis may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module hardware currently connected to the Opto as possible. For analog cards I can retrieve the type/model of the module, whereas for digital it just says “Dig/None”. So I can’t get the model or even know if there is something connected in that slot. I saw an older post that seems to confirm that you just h...... <less MMP via Java? - old forum post Forum - Published: ashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the...moreashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the protocol for memory mapping using Java or if anyone knows where it can be found? I have started to duplicate it by going along with the c++ code from the toolkit but was wondering if there was an easier way to do it? Thanks Report 02-13-2009, 9:39 AM ben orchard Joined on 12-08-2004 Posts 33 Re: Java P...... <less Share data between EPICs (MQTT vs VPN)? Forum - Published: How do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very...moreHow do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very soon. For each facility, I have dashboard set up locally. These facilities, while they are remote, are connected to single VPN. We have HQ where our bosses sit. I plan to set up groov EPIC there to have a dashboard that will display data from remote facilities.... <less Read Entire Ignition Tag Arrays Using Loops & Dynamic Settings Forum - Published: Ignition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have...moreIgnition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have some part of each element’s name be the index. For example, you may have: strings/myAlarms/Alarm[0] , ../Alarm[1] , ../Alarm[2] , and ../Alarm[3] as an array of Alarm strings. While in this example they all exist in the one myAlarms folder, each element is an individual tag. So, if you want use Nod...... <less Mosquitto MQTT server in old cellphone Forum - Published: Hi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the...moreHi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the app Termux (linux terminal emulator) in order to run Mosquitto in the device, the PR1 nodered receives the data with no issues and I have performed intense testing and integrated with several devices. It works perfectly even with heavy loads and the built in battery gives me a lot of flexibility no...... <less « PreviousPage 2 of 6Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
OptoMMP Tool kit? Forum - Published: Is this version specific? i.e. Can the latest version be used with Pac Control 8.5? Which version has ActiveX controls that supports Legacy VisualBasic applications (VB 6.0)? Thanks....Is this version specific? i.e. Can the latest version be used with Pac Control 8.5? Which version has ActiveX controls that supports Legacy VisualBasic applications (VB 6.0)? Thanks.... <less Groov EPIC-PR1 - Restful API Forum - Published: Hey Guys, I might be missing it, but is there no restful api for the EPIC-PR1 like the snap-pac-r1/r2? I know that we can build a similar function like it through node-red, but wouldn’t it make sense...moreHey Guys, I might be missing it, but is there no restful api for the EPIC-PR1 like the snap-pac-r1/r2? I know that we can build a similar function like it through node-red, but wouldn’t it make sense just to have it baked in as well? Saves a lot of work and testing. I am using a mixture of PR1 & R2’s, mainly because I need reliable serial comms for modbus RTU. Once the serial module is ready for the PR1, I will be swapping a lot and changing future builds. It would be nice to use my curren...... <less PAC Project Versions Forum - Published: Almost 95% of my projects were created with PAC Project version R9.6003-86. On one of my PCs, I must have used a more recent version maybe R9.6004-109, R9.6005-125 or R9.6006-131. First off, how can I...moreAlmost 95% of my projects were created with PAC Project version R9.6003-86. On one of my PCs, I must have used a more recent version maybe R9.6004-109, R9.6005-125 or R9.6006-131. First off, how can I tell which PAC Project this PC is running. (sure, I can see Control is R9.6e, Display is R9.6F Build 0092 and SoftPAC is v.R9.6a, but what Project version installed those?) Secondly, can I reinstall R9.6003-86 on this same PC and both versions will work (maybe in a different location on my PC)? L...... <less Max number of trends in a project? Forum - Published: Is there a maximum number of trends in a project? I keep trying to add one and the trend gadget just crashes/never loads in ‘View’. I have tried interactive and classic. trend_crash.png1068×329 21.3...moreIs there a maximum number of trends in a project? I keep trying to add one and the trend gadget just crashes/never loads in ‘View’. I have tried interactive and classic. trend_crash.png1068×329 21.3 KB The values to the left are the same values used in the trend.... <less Which groov EPIC Module for humidity sensor? Forum - Published: Hi Ma’am/Sir, May I ask if what module can read a humidity sensor? I have already created in our Data Center a Temperature Monitoring and used the GRV-ITMI-8 module. Thanks in advance. Best Regards, Jay...Hi Ma’am/Sir, May I ask if what module can read a humidity sensor? I have already created in our Data Center a Temperature Monitoring and used the GRV-ITMI-8 module. Thanks in advance. Best Regards, Jay... <less SNAP-OMR6 vs SNAP-ODC5R. Mechanical relay ouput modules Forum - Published: It still surprises me how many people work with Opto 22 hardware and software and yet are not signed up to OptoNews and so miss out on hearing all the cool stuff that happens in the world of Opto 22...moreIt still surprises me how many people work with Opto 22 hardware and software and yet are not signed up to OptoNews and so miss out on hearing all the cool stuff that happens in the world of Opto 22… Another topic for another day perhaps, right now I just want to answer a question about our new digital output modules which got announced in[URL=“http://www.opto22.com/site/optonews/2011/optonews_08312011.aspx”] last week’s OptoNews. SNAP-OMR6. 4 channels of 6 amp mechanical relay goodness, more th...... <less A pulse signal generated by the Holzer sensor Forum - Published: Excuse me, a pulse signal generated by the Holzer sensor, can use the IDC5 count? If not, what kind of module is used? Thank you...Excuse me, a pulse signal generated by the Holzer sensor, can use the IDC5 count? If not, what kind of module is used? Thank you... <less Fonts rendered at different sizes for different controls Forum - Published: I’ve come across a minor inconsistency with the size text is rendered for the Button control and the Text object. In typical WinForms applications these fonts would be displayed the same size if they...moreI’ve come across a minor inconsistency with the size text is rendered for the Button control and the Text object. In typical WinForms applications these fonts would be displayed the same size if they are configured to the same font size. I’ve attached a screen shot that illustrates the difference, both of these controls are set to: MS Sans Serif Bold 20pt Is this a known issue? different font sizes on controls.png818×506 8.23 KB Regards, Steve... <less Radio button-like behavior Forum - Published: Greetings OptoFans, I recently had someone ask me for some sample code to make use of a loop in OptoScript. In his application, he has several user choices (in an integer table), and wants those...more Greetings OptoFans, I recently had someone ask me for some sample code to make use of a loop in OptoScript. In his application, he has several user choices (in an integer table), and wants those options to act like radio buttons. In other words, if one choice is selected, the others are de-selected. He originally solved this with multiple if statements but was looking for a loop option. Here’s his original code and my suggested loop. I’m hoping you Clever People Out There in OptoLand will have ...... <less Selecting a Solid state relay for a 1HP 120VAC motor Forum - Published: I have a customer with a 1HP 120VAC pump ùsing a smart device to time and control it. Another person has tried some generic 25A 250V and 40A 380V SSRs with all failure. One 25A unit faled-open, one...moreI have a customer with a 1HP 120VAC pump ùsing a smart device to time and control it. Another person has tried some generic 25A 250V and 40A 380V SSRs with all failure. One 25A unit faled-open, one failed-closed(shorted), and the 40A unit failed-closed. All had heat sinks with proper compound. I have assured this new customer that we can provide a reliable permanent solution, using an Opto22 product by an American company. What will be the best O22 SSR product to use for this application? And ...... <less Capture the edge of a state change Forum - Published: I develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a...moreI develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a comparison between LastState and the current value, if they are different I update the LastState variable to the current state and perform the required reaction. if ((InputPoint=1) and (LastState=0)) Then LastState=1; Perform whatever reaction should happen at the on edge elseif ((InputPoint=0) and (Last...... <less Groov Box Communication Error When Trying to read Static Tags Forum - Published: Getting this error when trying to access static tags in groov. How can I resolve this?... Getting this error when trying to access static tags in groov. How can I resolve this?... <less Long Epic Boot Time Forum - Published: First time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a...moreFirst time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a thin client as the HMI and I had to add an output that the strategy turns on to power the HMI when the EPIC was ready. The thin client boots much faster and can’t connect to the EPIC because it wasn’t ready. Now, though, the output comes on but the EPIC is still not ready so I have to add an additi...... <less FT232H to Flash Forum - Published: Hello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am...moreHello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am really trying to talk to the chip through a GROOV EPIC microcontroller through SSH PUTTY. Through this way, I can only get to trying to talk to the chip by git cloning to the site on putty through “git clone GitHub - optodeveloper/SSH-Demo” through that, I talked to the USB port through “/dev/ttyS...... <less What does "edge programmable" mean? Forum - Published: According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”....According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”.... <less Detect I/O Module Being Used Forum - Published: This may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module...moreThis may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module hardware currently connected to the Opto as possible. For analog cards I can retrieve the type/model of the module, whereas for digital it just says “Dig/None”. So I can’t get the model or even know if there is something connected in that slot. I saw an older post that seems to confirm that you just h...... <less MMP via Java? - old forum post Forum - Published: ashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the...moreashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the protocol for memory mapping using Java or if anyone knows where it can be found? I have started to duplicate it by going along with the c++ code from the toolkit but was wondering if there was an easier way to do it? Thanks Report 02-13-2009, 9:39 AM ben orchard Joined on 12-08-2004 Posts 33 Re: Java P...... <less Share data between EPICs (MQTT vs VPN)? Forum - Published: How do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very...moreHow do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very soon. For each facility, I have dashboard set up locally. These facilities, while they are remote, are connected to single VPN. We have HQ where our bosses sit. I plan to set up groov EPIC there to have a dashboard that will display data from remote facilities.... <less Read Entire Ignition Tag Arrays Using Loops & Dynamic Settings Forum - Published: Ignition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have...moreIgnition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have some part of each element’s name be the index. For example, you may have: strings/myAlarms/Alarm[0] , ../Alarm[1] , ../Alarm[2] , and ../Alarm[3] as an array of Alarm strings. While in this example they all exist in the one myAlarms folder, each element is an individual tag. So, if you want use Nod...... <less Mosquitto MQTT server in old cellphone Forum - Published: Hi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the...moreHi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the app Termux (linux terminal emulator) in order to run Mosquitto in the device, the PR1 nodered receives the data with no issues and I have performed intense testing and integrated with several devices. It works perfectly even with heavy loads and the built in battery gives me a lot of flexibility no...... <less « PreviousPage 2 of 6Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Groov EPIC-PR1 - Restful API Forum - Published: Hey Guys, I might be missing it, but is there no restful api for the EPIC-PR1 like the snap-pac-r1/r2? I know that we can build a similar function like it through node-red, but wouldn’t it make sense...moreHey Guys, I might be missing it, but is there no restful api for the EPIC-PR1 like the snap-pac-r1/r2? I know that we can build a similar function like it through node-red, but wouldn’t it make sense just to have it baked in as well? Saves a lot of work and testing. I am using a mixture of PR1 & R2’s, mainly because I need reliable serial comms for modbus RTU. Once the serial module is ready for the PR1, I will be swapping a lot and changing future builds. It would be nice to use my curren...... <less PAC Project Versions Forum - Published: Almost 95% of my projects were created with PAC Project version R9.6003-86. On one of my PCs, I must have used a more recent version maybe R9.6004-109, R9.6005-125 or R9.6006-131. First off, how can I...moreAlmost 95% of my projects were created with PAC Project version R9.6003-86. On one of my PCs, I must have used a more recent version maybe R9.6004-109, R9.6005-125 or R9.6006-131. First off, how can I tell which PAC Project this PC is running. (sure, I can see Control is R9.6e, Display is R9.6F Build 0092 and SoftPAC is v.R9.6a, but what Project version installed those?) Secondly, can I reinstall R9.6003-86 on this same PC and both versions will work (maybe in a different location on my PC)? L...... <less Max number of trends in a project? Forum - Published: Is there a maximum number of trends in a project? I keep trying to add one and the trend gadget just crashes/never loads in ‘View’. I have tried interactive and classic. trend_crash.png1068×329 21.3...moreIs there a maximum number of trends in a project? I keep trying to add one and the trend gadget just crashes/never loads in ‘View’. I have tried interactive and classic. trend_crash.png1068×329 21.3 KB The values to the left are the same values used in the trend.... <less Which groov EPIC Module for humidity sensor? Forum - Published: Hi Ma’am/Sir, May I ask if what module can read a humidity sensor? I have already created in our Data Center a Temperature Monitoring and used the GRV-ITMI-8 module. Thanks in advance. Best Regards, Jay...Hi Ma’am/Sir, May I ask if what module can read a humidity sensor? I have already created in our Data Center a Temperature Monitoring and used the GRV-ITMI-8 module. Thanks in advance. Best Regards, Jay... <less SNAP-OMR6 vs SNAP-ODC5R. Mechanical relay ouput modules Forum - Published: It still surprises me how many people work with Opto 22 hardware and software and yet are not signed up to OptoNews and so miss out on hearing all the cool stuff that happens in the world of Opto 22...moreIt still surprises me how many people work with Opto 22 hardware and software and yet are not signed up to OptoNews and so miss out on hearing all the cool stuff that happens in the world of Opto 22… Another topic for another day perhaps, right now I just want to answer a question about our new digital output modules which got announced in[URL=“http://www.opto22.com/site/optonews/2011/optonews_08312011.aspx”] last week’s OptoNews. SNAP-OMR6. 4 channels of 6 amp mechanical relay goodness, more th...... <less A pulse signal generated by the Holzer sensor Forum - Published: Excuse me, a pulse signal generated by the Holzer sensor, can use the IDC5 count? If not, what kind of module is used? Thank you...Excuse me, a pulse signal generated by the Holzer sensor, can use the IDC5 count? If not, what kind of module is used? Thank you... <less Fonts rendered at different sizes for different controls Forum - Published: I’ve come across a minor inconsistency with the size text is rendered for the Button control and the Text object. In typical WinForms applications these fonts would be displayed the same size if they...moreI’ve come across a minor inconsistency with the size text is rendered for the Button control and the Text object. In typical WinForms applications these fonts would be displayed the same size if they are configured to the same font size. I’ve attached a screen shot that illustrates the difference, both of these controls are set to: MS Sans Serif Bold 20pt Is this a known issue? different font sizes on controls.png818×506 8.23 KB Regards, Steve... <less Radio button-like behavior Forum - Published: Greetings OptoFans, I recently had someone ask me for some sample code to make use of a loop in OptoScript. In his application, he has several user choices (in an integer table), and wants those...more Greetings OptoFans, I recently had someone ask me for some sample code to make use of a loop in OptoScript. In his application, he has several user choices (in an integer table), and wants those options to act like radio buttons. In other words, if one choice is selected, the others are de-selected. He originally solved this with multiple if statements but was looking for a loop option. Here’s his original code and my suggested loop. I’m hoping you Clever People Out There in OptoLand will have ...... <less Selecting a Solid state relay for a 1HP 120VAC motor Forum - Published: I have a customer with a 1HP 120VAC pump ùsing a smart device to time and control it. Another person has tried some generic 25A 250V and 40A 380V SSRs with all failure. One 25A unit faled-open, one...moreI have a customer with a 1HP 120VAC pump ùsing a smart device to time and control it. Another person has tried some generic 25A 250V and 40A 380V SSRs with all failure. One 25A unit faled-open, one failed-closed(shorted), and the 40A unit failed-closed. All had heat sinks with proper compound. I have assured this new customer that we can provide a reliable permanent solution, using an Opto22 product by an American company. What will be the best O22 SSR product to use for this application? And ...... <less Capture the edge of a state change Forum - Published: I develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a...moreI develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a comparison between LastState and the current value, if they are different I update the LastState variable to the current state and perform the required reaction. if ((InputPoint=1) and (LastState=0)) Then LastState=1; Perform whatever reaction should happen at the on edge elseif ((InputPoint=0) and (Last...... <less Groov Box Communication Error When Trying to read Static Tags Forum - Published: Getting this error when trying to access static tags in groov. How can I resolve this?... Getting this error when trying to access static tags in groov. How can I resolve this?... <less Long Epic Boot Time Forum - Published: First time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a...moreFirst time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a thin client as the HMI and I had to add an output that the strategy turns on to power the HMI when the EPIC was ready. The thin client boots much faster and can’t connect to the EPIC because it wasn’t ready. Now, though, the output comes on but the EPIC is still not ready so I have to add an additi...... <less FT232H to Flash Forum - Published: Hello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am...moreHello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am really trying to talk to the chip through a GROOV EPIC microcontroller through SSH PUTTY. Through this way, I can only get to trying to talk to the chip by git cloning to the site on putty through “git clone GitHub - optodeveloper/SSH-Demo” through that, I talked to the USB port through “/dev/ttyS...... <less What does "edge programmable" mean? Forum - Published: According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”....According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”.... <less Detect I/O Module Being Used Forum - Published: This may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module...moreThis may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module hardware currently connected to the Opto as possible. For analog cards I can retrieve the type/model of the module, whereas for digital it just says “Dig/None”. So I can’t get the model or even know if there is something connected in that slot. I saw an older post that seems to confirm that you just h...... <less MMP via Java? - old forum post Forum - Published: ashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the...moreashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the protocol for memory mapping using Java or if anyone knows where it can be found? I have started to duplicate it by going along with the c++ code from the toolkit but was wondering if there was an easier way to do it? Thanks Report 02-13-2009, 9:39 AM ben orchard Joined on 12-08-2004 Posts 33 Re: Java P...... <less Share data between EPICs (MQTT vs VPN)? Forum - Published: How do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very...moreHow do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very soon. For each facility, I have dashboard set up locally. These facilities, while they are remote, are connected to single VPN. We have HQ where our bosses sit. I plan to set up groov EPIC there to have a dashboard that will display data from remote facilities.... <less Read Entire Ignition Tag Arrays Using Loops & Dynamic Settings Forum - Published: Ignition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have...moreIgnition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have some part of each element’s name be the index. For example, you may have: strings/myAlarms/Alarm[0] , ../Alarm[1] , ../Alarm[2] , and ../Alarm[3] as an array of Alarm strings. While in this example they all exist in the one myAlarms folder, each element is an individual tag. So, if you want use Nod...... <less Mosquitto MQTT server in old cellphone Forum - Published: Hi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the...moreHi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the app Termux (linux terminal emulator) in order to run Mosquitto in the device, the PR1 nodered receives the data with no issues and I have performed intense testing and integrated with several devices. It works perfectly even with heavy loads and the built in battery gives me a lot of flexibility no...... <less « PreviousPage 2 of 6Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
PAC Project Versions Forum - Published: Almost 95% of my projects were created with PAC Project version R9.6003-86. On one of my PCs, I must have used a more recent version maybe R9.6004-109, R9.6005-125 or R9.6006-131. First off, how can I...moreAlmost 95% of my projects were created with PAC Project version R9.6003-86. On one of my PCs, I must have used a more recent version maybe R9.6004-109, R9.6005-125 or R9.6006-131. First off, how can I tell which PAC Project this PC is running. (sure, I can see Control is R9.6e, Display is R9.6F Build 0092 and SoftPAC is v.R9.6a, but what Project version installed those?) Secondly, can I reinstall R9.6003-86 on this same PC and both versions will work (maybe in a different location on my PC)? L...... <less Max number of trends in a project? Forum - Published: Is there a maximum number of trends in a project? I keep trying to add one and the trend gadget just crashes/never loads in ‘View’. I have tried interactive and classic. trend_crash.png1068×329 21.3...moreIs there a maximum number of trends in a project? I keep trying to add one and the trend gadget just crashes/never loads in ‘View’. I have tried interactive and classic. trend_crash.png1068×329 21.3 KB The values to the left are the same values used in the trend.... <less Which groov EPIC Module for humidity sensor? Forum - Published: Hi Ma’am/Sir, May I ask if what module can read a humidity sensor? I have already created in our Data Center a Temperature Monitoring and used the GRV-ITMI-8 module. Thanks in advance. Best Regards, Jay...Hi Ma’am/Sir, May I ask if what module can read a humidity sensor? I have already created in our Data Center a Temperature Monitoring and used the GRV-ITMI-8 module. Thanks in advance. Best Regards, Jay... <less SNAP-OMR6 vs SNAP-ODC5R. Mechanical relay ouput modules Forum - Published: It still surprises me how many people work with Opto 22 hardware and software and yet are not signed up to OptoNews and so miss out on hearing all the cool stuff that happens in the world of Opto 22...moreIt still surprises me how many people work with Opto 22 hardware and software and yet are not signed up to OptoNews and so miss out on hearing all the cool stuff that happens in the world of Opto 22… Another topic for another day perhaps, right now I just want to answer a question about our new digital output modules which got announced in[URL=“http://www.opto22.com/site/optonews/2011/optonews_08312011.aspx”] last week’s OptoNews. SNAP-OMR6. 4 channels of 6 amp mechanical relay goodness, more th...... <less A pulse signal generated by the Holzer sensor Forum - Published: Excuse me, a pulse signal generated by the Holzer sensor, can use the IDC5 count? If not, what kind of module is used? Thank you...Excuse me, a pulse signal generated by the Holzer sensor, can use the IDC5 count? If not, what kind of module is used? Thank you... <less Fonts rendered at different sizes for different controls Forum - Published: I’ve come across a minor inconsistency with the size text is rendered for the Button control and the Text object. In typical WinForms applications these fonts would be displayed the same size if they...moreI’ve come across a minor inconsistency with the size text is rendered for the Button control and the Text object. In typical WinForms applications these fonts would be displayed the same size if they are configured to the same font size. I’ve attached a screen shot that illustrates the difference, both of these controls are set to: MS Sans Serif Bold 20pt Is this a known issue? different font sizes on controls.png818×506 8.23 KB Regards, Steve... <less Radio button-like behavior Forum - Published: Greetings OptoFans, I recently had someone ask me for some sample code to make use of a loop in OptoScript. In his application, he has several user choices (in an integer table), and wants those...more Greetings OptoFans, I recently had someone ask me for some sample code to make use of a loop in OptoScript. In his application, he has several user choices (in an integer table), and wants those options to act like radio buttons. In other words, if one choice is selected, the others are de-selected. He originally solved this with multiple if statements but was looking for a loop option. Here’s his original code and my suggested loop. I’m hoping you Clever People Out There in OptoLand will have ...... <less Selecting a Solid state relay for a 1HP 120VAC motor Forum - Published: I have a customer with a 1HP 120VAC pump ùsing a smart device to time and control it. Another person has tried some generic 25A 250V and 40A 380V SSRs with all failure. One 25A unit faled-open, one...moreI have a customer with a 1HP 120VAC pump ùsing a smart device to time and control it. Another person has tried some generic 25A 250V and 40A 380V SSRs with all failure. One 25A unit faled-open, one failed-closed(shorted), and the 40A unit failed-closed. All had heat sinks with proper compound. I have assured this new customer that we can provide a reliable permanent solution, using an Opto22 product by an American company. What will be the best O22 SSR product to use for this application? And ...... <less Capture the edge of a state change Forum - Published: I develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a...moreI develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a comparison between LastState and the current value, if they are different I update the LastState variable to the current state and perform the required reaction. if ((InputPoint=1) and (LastState=0)) Then LastState=1; Perform whatever reaction should happen at the on edge elseif ((InputPoint=0) and (Last...... <less Groov Box Communication Error When Trying to read Static Tags Forum - Published: Getting this error when trying to access static tags in groov. How can I resolve this?... Getting this error when trying to access static tags in groov. How can I resolve this?... <less Long Epic Boot Time Forum - Published: First time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a...moreFirst time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a thin client as the HMI and I had to add an output that the strategy turns on to power the HMI when the EPIC was ready. The thin client boots much faster and can’t connect to the EPIC because it wasn’t ready. Now, though, the output comes on but the EPIC is still not ready so I have to add an additi...... <less FT232H to Flash Forum - Published: Hello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am...moreHello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am really trying to talk to the chip through a GROOV EPIC microcontroller through SSH PUTTY. Through this way, I can only get to trying to talk to the chip by git cloning to the site on putty through “git clone GitHub - optodeveloper/SSH-Demo” through that, I talked to the USB port through “/dev/ttyS...... <less What does "edge programmable" mean? Forum - Published: According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”....According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”.... <less Detect I/O Module Being Used Forum - Published: This may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module...moreThis may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module hardware currently connected to the Opto as possible. For analog cards I can retrieve the type/model of the module, whereas for digital it just says “Dig/None”. So I can’t get the model or even know if there is something connected in that slot. I saw an older post that seems to confirm that you just h...... <less MMP via Java? - old forum post Forum - Published: ashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the...moreashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the protocol for memory mapping using Java or if anyone knows where it can be found? I have started to duplicate it by going along with the c++ code from the toolkit but was wondering if there was an easier way to do it? Thanks Report 02-13-2009, 9:39 AM ben orchard Joined on 12-08-2004 Posts 33 Re: Java P...... <less Share data between EPICs (MQTT vs VPN)? Forum - Published: How do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very...moreHow do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very soon. For each facility, I have dashboard set up locally. These facilities, while they are remote, are connected to single VPN. We have HQ where our bosses sit. I plan to set up groov EPIC there to have a dashboard that will display data from remote facilities.... <less Read Entire Ignition Tag Arrays Using Loops & Dynamic Settings Forum - Published: Ignition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have...moreIgnition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have some part of each element’s name be the index. For example, you may have: strings/myAlarms/Alarm[0] , ../Alarm[1] , ../Alarm[2] , and ../Alarm[3] as an array of Alarm strings. While in this example they all exist in the one myAlarms folder, each element is an individual tag. So, if you want use Nod...... <less Mosquitto MQTT server in old cellphone Forum - Published: Hi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the...moreHi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the app Termux (linux terminal emulator) in order to run Mosquitto in the device, the PR1 nodered receives the data with no issues and I have performed intense testing and integrated with several devices. It works perfectly even with heavy loads and the built in battery gives me a lot of flexibility no...... <less « PreviousPage 2 of 6Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Max number of trends in a project? Forum - Published: Is there a maximum number of trends in a project? I keep trying to add one and the trend gadget just crashes/never loads in ‘View’. I have tried interactive and classic. trend_crash.png1068×329 21.3...moreIs there a maximum number of trends in a project? I keep trying to add one and the trend gadget just crashes/never loads in ‘View’. I have tried interactive and classic. trend_crash.png1068×329 21.3 KB The values to the left are the same values used in the trend.... <less Which groov EPIC Module for humidity sensor? Forum - Published: Hi Ma’am/Sir, May I ask if what module can read a humidity sensor? I have already created in our Data Center a Temperature Monitoring and used the GRV-ITMI-8 module. Thanks in advance. Best Regards, Jay...Hi Ma’am/Sir, May I ask if what module can read a humidity sensor? I have already created in our Data Center a Temperature Monitoring and used the GRV-ITMI-8 module. Thanks in advance. Best Regards, Jay... <less SNAP-OMR6 vs SNAP-ODC5R. Mechanical relay ouput modules Forum - Published: It still surprises me how many people work with Opto 22 hardware and software and yet are not signed up to OptoNews and so miss out on hearing all the cool stuff that happens in the world of Opto 22...moreIt still surprises me how many people work with Opto 22 hardware and software and yet are not signed up to OptoNews and so miss out on hearing all the cool stuff that happens in the world of Opto 22… Another topic for another day perhaps, right now I just want to answer a question about our new digital output modules which got announced in[URL=“http://www.opto22.com/site/optonews/2011/optonews_08312011.aspx”] last week’s OptoNews. SNAP-OMR6. 4 channels of 6 amp mechanical relay goodness, more th...... <less A pulse signal generated by the Holzer sensor Forum - Published: Excuse me, a pulse signal generated by the Holzer sensor, can use the IDC5 count? If not, what kind of module is used? Thank you...Excuse me, a pulse signal generated by the Holzer sensor, can use the IDC5 count? If not, what kind of module is used? Thank you... <less Fonts rendered at different sizes for different controls Forum - Published: I’ve come across a minor inconsistency with the size text is rendered for the Button control and the Text object. In typical WinForms applications these fonts would be displayed the same size if they...moreI’ve come across a minor inconsistency with the size text is rendered for the Button control and the Text object. In typical WinForms applications these fonts would be displayed the same size if they are configured to the same font size. I’ve attached a screen shot that illustrates the difference, both of these controls are set to: MS Sans Serif Bold 20pt Is this a known issue? different font sizes on controls.png818×506 8.23 KB Regards, Steve... <less Radio button-like behavior Forum - Published: Greetings OptoFans, I recently had someone ask me for some sample code to make use of a loop in OptoScript. In his application, he has several user choices (in an integer table), and wants those...more Greetings OptoFans, I recently had someone ask me for some sample code to make use of a loop in OptoScript. In his application, he has several user choices (in an integer table), and wants those options to act like radio buttons. In other words, if one choice is selected, the others are de-selected. He originally solved this with multiple if statements but was looking for a loop option. Here’s his original code and my suggested loop. I’m hoping you Clever People Out There in OptoLand will have ...... <less Selecting a Solid state relay for a 1HP 120VAC motor Forum - Published: I have a customer with a 1HP 120VAC pump ùsing a smart device to time and control it. Another person has tried some generic 25A 250V and 40A 380V SSRs with all failure. One 25A unit faled-open, one...moreI have a customer with a 1HP 120VAC pump ùsing a smart device to time and control it. Another person has tried some generic 25A 250V and 40A 380V SSRs with all failure. One 25A unit faled-open, one failed-closed(shorted), and the 40A unit failed-closed. All had heat sinks with proper compound. I have assured this new customer that we can provide a reliable permanent solution, using an Opto22 product by an American company. What will be the best O22 SSR product to use for this application? And ...... <less Capture the edge of a state change Forum - Published: I develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a...moreI develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a comparison between LastState and the current value, if they are different I update the LastState variable to the current state and perform the required reaction. if ((InputPoint=1) and (LastState=0)) Then LastState=1; Perform whatever reaction should happen at the on edge elseif ((InputPoint=0) and (Last...... <less Groov Box Communication Error When Trying to read Static Tags Forum - Published: Getting this error when trying to access static tags in groov. How can I resolve this?... Getting this error when trying to access static tags in groov. How can I resolve this?... <less Long Epic Boot Time Forum - Published: First time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a...moreFirst time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a thin client as the HMI and I had to add an output that the strategy turns on to power the HMI when the EPIC was ready. The thin client boots much faster and can’t connect to the EPIC because it wasn’t ready. Now, though, the output comes on but the EPIC is still not ready so I have to add an additi...... <less FT232H to Flash Forum - Published: Hello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am...moreHello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am really trying to talk to the chip through a GROOV EPIC microcontroller through SSH PUTTY. Through this way, I can only get to trying to talk to the chip by git cloning to the site on putty through “git clone GitHub - optodeveloper/SSH-Demo” through that, I talked to the USB port through “/dev/ttyS...... <less What does "edge programmable" mean? Forum - Published: According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”....According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”.... <less Detect I/O Module Being Used Forum - Published: This may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module...moreThis may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module hardware currently connected to the Opto as possible. For analog cards I can retrieve the type/model of the module, whereas for digital it just says “Dig/None”. So I can’t get the model or even know if there is something connected in that slot. I saw an older post that seems to confirm that you just h...... <less MMP via Java? - old forum post Forum - Published: ashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the...moreashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the protocol for memory mapping using Java or if anyone knows where it can be found? I have started to duplicate it by going along with the c++ code from the toolkit but was wondering if there was an easier way to do it? Thanks Report 02-13-2009, 9:39 AM ben orchard Joined on 12-08-2004 Posts 33 Re: Java P...... <less Share data between EPICs (MQTT vs VPN)? Forum - Published: How do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very...moreHow do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very soon. For each facility, I have dashboard set up locally. These facilities, while they are remote, are connected to single VPN. We have HQ where our bosses sit. I plan to set up groov EPIC there to have a dashboard that will display data from remote facilities.... <less Read Entire Ignition Tag Arrays Using Loops & Dynamic Settings Forum - Published: Ignition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have...moreIgnition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have some part of each element’s name be the index. For example, you may have: strings/myAlarms/Alarm[0] , ../Alarm[1] , ../Alarm[2] , and ../Alarm[3] as an array of Alarm strings. While in this example they all exist in the one myAlarms folder, each element is an individual tag. So, if you want use Nod...... <less Mosquitto MQTT server in old cellphone Forum - Published: Hi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the...moreHi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the app Termux (linux terminal emulator) in order to run Mosquitto in the device, the PR1 nodered receives the data with no issues and I have performed intense testing and integrated with several devices. It works perfectly even with heavy loads and the built in battery gives me a lot of flexibility no...... <less « PreviousPage 2 of 6Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Which groov EPIC Module for humidity sensor? Forum - Published: Hi Ma’am/Sir, May I ask if what module can read a humidity sensor? I have already created in our Data Center a Temperature Monitoring and used the GRV-ITMI-8 module. Thanks in advance. Best Regards, Jay...Hi Ma’am/Sir, May I ask if what module can read a humidity sensor? I have already created in our Data Center a Temperature Monitoring and used the GRV-ITMI-8 module. Thanks in advance. Best Regards, Jay... <less SNAP-OMR6 vs SNAP-ODC5R. Mechanical relay ouput modules Forum - Published: It still surprises me how many people work with Opto 22 hardware and software and yet are not signed up to OptoNews and so miss out on hearing all the cool stuff that happens in the world of Opto 22...moreIt still surprises me how many people work with Opto 22 hardware and software and yet are not signed up to OptoNews and so miss out on hearing all the cool stuff that happens in the world of Opto 22… Another topic for another day perhaps, right now I just want to answer a question about our new digital output modules which got announced in[URL=“http://www.opto22.com/site/optonews/2011/optonews_08312011.aspx”] last week’s OptoNews. SNAP-OMR6. 4 channels of 6 amp mechanical relay goodness, more th...... <less A pulse signal generated by the Holzer sensor Forum - Published: Excuse me, a pulse signal generated by the Holzer sensor, can use the IDC5 count? If not, what kind of module is used? Thank you...Excuse me, a pulse signal generated by the Holzer sensor, can use the IDC5 count? If not, what kind of module is used? Thank you... <less Fonts rendered at different sizes for different controls Forum - Published: I’ve come across a minor inconsistency with the size text is rendered for the Button control and the Text object. In typical WinForms applications these fonts would be displayed the same size if they...moreI’ve come across a minor inconsistency with the size text is rendered for the Button control and the Text object. In typical WinForms applications these fonts would be displayed the same size if they are configured to the same font size. I’ve attached a screen shot that illustrates the difference, both of these controls are set to: MS Sans Serif Bold 20pt Is this a known issue? different font sizes on controls.png818×506 8.23 KB Regards, Steve... <less Radio button-like behavior Forum - Published: Greetings OptoFans, I recently had someone ask me for some sample code to make use of a loop in OptoScript. In his application, he has several user choices (in an integer table), and wants those...more Greetings OptoFans, I recently had someone ask me for some sample code to make use of a loop in OptoScript. In his application, he has several user choices (in an integer table), and wants those options to act like radio buttons. In other words, if one choice is selected, the others are de-selected. He originally solved this with multiple if statements but was looking for a loop option. Here’s his original code and my suggested loop. I’m hoping you Clever People Out There in OptoLand will have ...... <less Selecting a Solid state relay for a 1HP 120VAC motor Forum - Published: I have a customer with a 1HP 120VAC pump ùsing a smart device to time and control it. Another person has tried some generic 25A 250V and 40A 380V SSRs with all failure. One 25A unit faled-open, one...moreI have a customer with a 1HP 120VAC pump ùsing a smart device to time and control it. Another person has tried some generic 25A 250V and 40A 380V SSRs with all failure. One 25A unit faled-open, one failed-closed(shorted), and the 40A unit failed-closed. All had heat sinks with proper compound. I have assured this new customer that we can provide a reliable permanent solution, using an Opto22 product by an American company. What will be the best O22 SSR product to use for this application? And ...... <less Capture the edge of a state change Forum - Published: I develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a...moreI develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a comparison between LastState and the current value, if they are different I update the LastState variable to the current state and perform the required reaction. if ((InputPoint=1) and (LastState=0)) Then LastState=1; Perform whatever reaction should happen at the on edge elseif ((InputPoint=0) and (Last...... <less Groov Box Communication Error When Trying to read Static Tags Forum - Published: Getting this error when trying to access static tags in groov. How can I resolve this?... Getting this error when trying to access static tags in groov. How can I resolve this?... <less Long Epic Boot Time Forum - Published: First time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a...moreFirst time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a thin client as the HMI and I had to add an output that the strategy turns on to power the HMI when the EPIC was ready. The thin client boots much faster and can’t connect to the EPIC because it wasn’t ready. Now, though, the output comes on but the EPIC is still not ready so I have to add an additi...... <less FT232H to Flash Forum - Published: Hello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am...moreHello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am really trying to talk to the chip through a GROOV EPIC microcontroller through SSH PUTTY. Through this way, I can only get to trying to talk to the chip by git cloning to the site on putty through “git clone GitHub - optodeveloper/SSH-Demo” through that, I talked to the USB port through “/dev/ttyS...... <less What does "edge programmable" mean? Forum - Published: According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”....According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”.... <less Detect I/O Module Being Used Forum - Published: This may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module...moreThis may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module hardware currently connected to the Opto as possible. For analog cards I can retrieve the type/model of the module, whereas for digital it just says “Dig/None”. So I can’t get the model or even know if there is something connected in that slot. I saw an older post that seems to confirm that you just h...... <less MMP via Java? - old forum post Forum - Published: ashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the...moreashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the protocol for memory mapping using Java or if anyone knows where it can be found? I have started to duplicate it by going along with the c++ code from the toolkit but was wondering if there was an easier way to do it? Thanks Report 02-13-2009, 9:39 AM ben orchard Joined on 12-08-2004 Posts 33 Re: Java P...... <less Share data between EPICs (MQTT vs VPN)? Forum - Published: How do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very...moreHow do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very soon. For each facility, I have dashboard set up locally. These facilities, while they are remote, are connected to single VPN. We have HQ where our bosses sit. I plan to set up groov EPIC there to have a dashboard that will display data from remote facilities.... <less Read Entire Ignition Tag Arrays Using Loops & Dynamic Settings Forum - Published: Ignition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have...moreIgnition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have some part of each element’s name be the index. For example, you may have: strings/myAlarms/Alarm[0] , ../Alarm[1] , ../Alarm[2] , and ../Alarm[3] as an array of Alarm strings. While in this example they all exist in the one myAlarms folder, each element is an individual tag. So, if you want use Nod...... <less Mosquitto MQTT server in old cellphone Forum - Published: Hi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the...moreHi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the app Termux (linux terminal emulator) in order to run Mosquitto in the device, the PR1 nodered receives the data with no issues and I have performed intense testing and integrated with several devices. It works perfectly even with heavy loads and the built in battery gives me a lot of flexibility no...... <less « PreviousPage 2 of 6Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
SNAP-OMR6 vs SNAP-ODC5R. Mechanical relay ouput modules Forum - Published: It still surprises me how many people work with Opto 22 hardware and software and yet are not signed up to OptoNews and so miss out on hearing all the cool stuff that happens in the world of Opto 22...moreIt still surprises me how many people work with Opto 22 hardware and software and yet are not signed up to OptoNews and so miss out on hearing all the cool stuff that happens in the world of Opto 22… Another topic for another day perhaps, right now I just want to answer a question about our new digital output modules which got announced in[URL=“http://www.opto22.com/site/optonews/2011/optonews_08312011.aspx”] last week’s OptoNews. SNAP-OMR6. 4 channels of 6 amp mechanical relay goodness, more th...... <less A pulse signal generated by the Holzer sensor Forum - Published: Excuse me, a pulse signal generated by the Holzer sensor, can use the IDC5 count? If not, what kind of module is used? Thank you...Excuse me, a pulse signal generated by the Holzer sensor, can use the IDC5 count? If not, what kind of module is used? Thank you... <less Fonts rendered at different sizes for different controls Forum - Published: I’ve come across a minor inconsistency with the size text is rendered for the Button control and the Text object. In typical WinForms applications these fonts would be displayed the same size if they...moreI’ve come across a minor inconsistency with the size text is rendered for the Button control and the Text object. In typical WinForms applications these fonts would be displayed the same size if they are configured to the same font size. I’ve attached a screen shot that illustrates the difference, both of these controls are set to: MS Sans Serif Bold 20pt Is this a known issue? different font sizes on controls.png818×506 8.23 KB Regards, Steve... <less Radio button-like behavior Forum - Published: Greetings OptoFans, I recently had someone ask me for some sample code to make use of a loop in OptoScript. In his application, he has several user choices (in an integer table), and wants those...more Greetings OptoFans, I recently had someone ask me for some sample code to make use of a loop in OptoScript. In his application, he has several user choices (in an integer table), and wants those options to act like radio buttons. In other words, if one choice is selected, the others are de-selected. He originally solved this with multiple if statements but was looking for a loop option. Here’s his original code and my suggested loop. I’m hoping you Clever People Out There in OptoLand will have ...... <less Selecting a Solid state relay for a 1HP 120VAC motor Forum - Published: I have a customer with a 1HP 120VAC pump ùsing a smart device to time and control it. Another person has tried some generic 25A 250V and 40A 380V SSRs with all failure. One 25A unit faled-open, one...moreI have a customer with a 1HP 120VAC pump ùsing a smart device to time and control it. Another person has tried some generic 25A 250V and 40A 380V SSRs with all failure. One 25A unit faled-open, one failed-closed(shorted), and the 40A unit failed-closed. All had heat sinks with proper compound. I have assured this new customer that we can provide a reliable permanent solution, using an Opto22 product by an American company. What will be the best O22 SSR product to use for this application? And ...... <less Capture the edge of a state change Forum - Published: I develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a...moreI develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a comparison between LastState and the current value, if they are different I update the LastState variable to the current state and perform the required reaction. if ((InputPoint=1) and (LastState=0)) Then LastState=1; Perform whatever reaction should happen at the on edge elseif ((InputPoint=0) and (Last...... <less Groov Box Communication Error When Trying to read Static Tags Forum - Published: Getting this error when trying to access static tags in groov. How can I resolve this?... Getting this error when trying to access static tags in groov. How can I resolve this?... <less Long Epic Boot Time Forum - Published: First time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a...moreFirst time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a thin client as the HMI and I had to add an output that the strategy turns on to power the HMI when the EPIC was ready. The thin client boots much faster and can’t connect to the EPIC because it wasn’t ready. Now, though, the output comes on but the EPIC is still not ready so I have to add an additi...... <less FT232H to Flash Forum - Published: Hello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am...moreHello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am really trying to talk to the chip through a GROOV EPIC microcontroller through SSH PUTTY. Through this way, I can only get to trying to talk to the chip by git cloning to the site on putty through “git clone GitHub - optodeveloper/SSH-Demo” through that, I talked to the USB port through “/dev/ttyS...... <less What does "edge programmable" mean? Forum - Published: According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”....According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”.... <less Detect I/O Module Being Used Forum - Published: This may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module...moreThis may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module hardware currently connected to the Opto as possible. For analog cards I can retrieve the type/model of the module, whereas for digital it just says “Dig/None”. So I can’t get the model or even know if there is something connected in that slot. I saw an older post that seems to confirm that you just h...... <less MMP via Java? - old forum post Forum - Published: ashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the...moreashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the protocol for memory mapping using Java or if anyone knows where it can be found? I have started to duplicate it by going along with the c++ code from the toolkit but was wondering if there was an easier way to do it? Thanks Report 02-13-2009, 9:39 AM ben orchard Joined on 12-08-2004 Posts 33 Re: Java P...... <less Share data between EPICs (MQTT vs VPN)? Forum - Published: How do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very...moreHow do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very soon. For each facility, I have dashboard set up locally. These facilities, while they are remote, are connected to single VPN. We have HQ where our bosses sit. I plan to set up groov EPIC there to have a dashboard that will display data from remote facilities.... <less Read Entire Ignition Tag Arrays Using Loops & Dynamic Settings Forum - Published: Ignition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have...moreIgnition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have some part of each element’s name be the index. For example, you may have: strings/myAlarms/Alarm[0] , ../Alarm[1] , ../Alarm[2] , and ../Alarm[3] as an array of Alarm strings. While in this example they all exist in the one myAlarms folder, each element is an individual tag. So, if you want use Nod...... <less Mosquitto MQTT server in old cellphone Forum - Published: Hi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the...moreHi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the app Termux (linux terminal emulator) in order to run Mosquitto in the device, the PR1 nodered receives the data with no issues and I have performed intense testing and integrated with several devices. It works perfectly even with heavy loads and the built in battery gives me a lot of flexibility no...... <less « PreviousPage 2 of 6Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
A pulse signal generated by the Holzer sensor Forum - Published: Excuse me, a pulse signal generated by the Holzer sensor, can use the IDC5 count? If not, what kind of module is used? Thank you...Excuse me, a pulse signal generated by the Holzer sensor, can use the IDC5 count? If not, what kind of module is used? Thank you... <less Fonts rendered at different sizes for different controls Forum - Published: I’ve come across a minor inconsistency with the size text is rendered for the Button control and the Text object. In typical WinForms applications these fonts would be displayed the same size if they...moreI’ve come across a minor inconsistency with the size text is rendered for the Button control and the Text object. In typical WinForms applications these fonts would be displayed the same size if they are configured to the same font size. I’ve attached a screen shot that illustrates the difference, both of these controls are set to: MS Sans Serif Bold 20pt Is this a known issue? different font sizes on controls.png818×506 8.23 KB Regards, Steve... <less Radio button-like behavior Forum - Published: Greetings OptoFans, I recently had someone ask me for some sample code to make use of a loop in OptoScript. In his application, he has several user choices (in an integer table), and wants those...more Greetings OptoFans, I recently had someone ask me for some sample code to make use of a loop in OptoScript. In his application, he has several user choices (in an integer table), and wants those options to act like radio buttons. In other words, if one choice is selected, the others are de-selected. He originally solved this with multiple if statements but was looking for a loop option. Here’s his original code and my suggested loop. I’m hoping you Clever People Out There in OptoLand will have ...... <less Selecting a Solid state relay for a 1HP 120VAC motor Forum - Published: I have a customer with a 1HP 120VAC pump ùsing a smart device to time and control it. Another person has tried some generic 25A 250V and 40A 380V SSRs with all failure. One 25A unit faled-open, one...moreI have a customer with a 1HP 120VAC pump ùsing a smart device to time and control it. Another person has tried some generic 25A 250V and 40A 380V SSRs with all failure. One 25A unit faled-open, one failed-closed(shorted), and the 40A unit failed-closed. All had heat sinks with proper compound. I have assured this new customer that we can provide a reliable permanent solution, using an Opto22 product by an American company. What will be the best O22 SSR product to use for this application? And ...... <less Capture the edge of a state change Forum - Published: I develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a...moreI develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a comparison between LastState and the current value, if they are different I update the LastState variable to the current state and perform the required reaction. if ((InputPoint=1) and (LastState=0)) Then LastState=1; Perform whatever reaction should happen at the on edge elseif ((InputPoint=0) and (Last...... <less Groov Box Communication Error When Trying to read Static Tags Forum - Published: Getting this error when trying to access static tags in groov. How can I resolve this?... Getting this error when trying to access static tags in groov. How can I resolve this?... <less Long Epic Boot Time Forum - Published: First time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a...moreFirst time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a thin client as the HMI and I had to add an output that the strategy turns on to power the HMI when the EPIC was ready. The thin client boots much faster and can’t connect to the EPIC because it wasn’t ready. Now, though, the output comes on but the EPIC is still not ready so I have to add an additi...... <less FT232H to Flash Forum - Published: Hello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am...moreHello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am really trying to talk to the chip through a GROOV EPIC microcontroller through SSH PUTTY. Through this way, I can only get to trying to talk to the chip by git cloning to the site on putty through “git clone GitHub - optodeveloper/SSH-Demo” through that, I talked to the USB port through “/dev/ttyS...... <less What does "edge programmable" mean? Forum - Published: According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”....According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”.... <less Detect I/O Module Being Used Forum - Published: This may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module...moreThis may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module hardware currently connected to the Opto as possible. For analog cards I can retrieve the type/model of the module, whereas for digital it just says “Dig/None”. So I can’t get the model or even know if there is something connected in that slot. I saw an older post that seems to confirm that you just h...... <less MMP via Java? - old forum post Forum - Published: ashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the...moreashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the protocol for memory mapping using Java or if anyone knows where it can be found? I have started to duplicate it by going along with the c++ code from the toolkit but was wondering if there was an easier way to do it? Thanks Report 02-13-2009, 9:39 AM ben orchard Joined on 12-08-2004 Posts 33 Re: Java P...... <less Share data between EPICs (MQTT vs VPN)? Forum - Published: How do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very...moreHow do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very soon. For each facility, I have dashboard set up locally. These facilities, while they are remote, are connected to single VPN. We have HQ where our bosses sit. I plan to set up groov EPIC there to have a dashboard that will display data from remote facilities.... <less Read Entire Ignition Tag Arrays Using Loops & Dynamic Settings Forum - Published: Ignition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have...moreIgnition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have some part of each element’s name be the index. For example, you may have: strings/myAlarms/Alarm[0] , ../Alarm[1] , ../Alarm[2] , and ../Alarm[3] as an array of Alarm strings. While in this example they all exist in the one myAlarms folder, each element is an individual tag. So, if you want use Nod...... <less Mosquitto MQTT server in old cellphone Forum - Published: Hi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the...moreHi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the app Termux (linux terminal emulator) in order to run Mosquitto in the device, the PR1 nodered receives the data with no issues and I have performed intense testing and integrated with several devices. It works perfectly even with heavy loads and the built in battery gives me a lot of flexibility no...... <less « PreviousPage 2 of 6Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Fonts rendered at different sizes for different controls Forum - Published: I’ve come across a minor inconsistency with the size text is rendered for the Button control and the Text object. In typical WinForms applications these fonts would be displayed the same size if they...moreI’ve come across a minor inconsistency with the size text is rendered for the Button control and the Text object. In typical WinForms applications these fonts would be displayed the same size if they are configured to the same font size. I’ve attached a screen shot that illustrates the difference, both of these controls are set to: MS Sans Serif Bold 20pt Is this a known issue? different font sizes on controls.png818×506 8.23 KB Regards, Steve... <less Radio button-like behavior Forum - Published: Greetings OptoFans, I recently had someone ask me for some sample code to make use of a loop in OptoScript. In his application, he has several user choices (in an integer table), and wants those...more Greetings OptoFans, I recently had someone ask me for some sample code to make use of a loop in OptoScript. In his application, he has several user choices (in an integer table), and wants those options to act like radio buttons. In other words, if one choice is selected, the others are de-selected. He originally solved this with multiple if statements but was looking for a loop option. Here’s his original code and my suggested loop. I’m hoping you Clever People Out There in OptoLand will have ...... <less Selecting a Solid state relay for a 1HP 120VAC motor Forum - Published: I have a customer with a 1HP 120VAC pump ùsing a smart device to time and control it. Another person has tried some generic 25A 250V and 40A 380V SSRs with all failure. One 25A unit faled-open, one...moreI have a customer with a 1HP 120VAC pump ùsing a smart device to time and control it. Another person has tried some generic 25A 250V and 40A 380V SSRs with all failure. One 25A unit faled-open, one failed-closed(shorted), and the 40A unit failed-closed. All had heat sinks with proper compound. I have assured this new customer that we can provide a reliable permanent solution, using an Opto22 product by an American company. What will be the best O22 SSR product to use for this application? And ...... <less Capture the edge of a state change Forum - Published: I develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a...moreI develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a comparison between LastState and the current value, if they are different I update the LastState variable to the current state and perform the required reaction. if ((InputPoint=1) and (LastState=0)) Then LastState=1; Perform whatever reaction should happen at the on edge elseif ((InputPoint=0) and (Last...... <less Groov Box Communication Error When Trying to read Static Tags Forum - Published: Getting this error when trying to access static tags in groov. How can I resolve this?... Getting this error when trying to access static tags in groov. How can I resolve this?... <less Long Epic Boot Time Forum - Published: First time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a...moreFirst time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a thin client as the HMI and I had to add an output that the strategy turns on to power the HMI when the EPIC was ready. The thin client boots much faster and can’t connect to the EPIC because it wasn’t ready. Now, though, the output comes on but the EPIC is still not ready so I have to add an additi...... <less FT232H to Flash Forum - Published: Hello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am...moreHello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am really trying to talk to the chip through a GROOV EPIC microcontroller through SSH PUTTY. Through this way, I can only get to trying to talk to the chip by git cloning to the site on putty through “git clone GitHub - optodeveloper/SSH-Demo” through that, I talked to the USB port through “/dev/ttyS...... <less What does "edge programmable" mean? Forum - Published: According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”....According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”.... <less Detect I/O Module Being Used Forum - Published: This may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module...moreThis may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module hardware currently connected to the Opto as possible. For analog cards I can retrieve the type/model of the module, whereas for digital it just says “Dig/None”. So I can’t get the model or even know if there is something connected in that slot. I saw an older post that seems to confirm that you just h...... <less MMP via Java? - old forum post Forum - Published: ashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the...moreashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the protocol for memory mapping using Java or if anyone knows where it can be found? I have started to duplicate it by going along with the c++ code from the toolkit but was wondering if there was an easier way to do it? Thanks Report 02-13-2009, 9:39 AM ben orchard Joined on 12-08-2004 Posts 33 Re: Java P...... <less Share data between EPICs (MQTT vs VPN)? Forum - Published: How do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very...moreHow do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very soon. For each facility, I have dashboard set up locally. These facilities, while they are remote, are connected to single VPN. We have HQ where our bosses sit. I plan to set up groov EPIC there to have a dashboard that will display data from remote facilities.... <less Read Entire Ignition Tag Arrays Using Loops & Dynamic Settings Forum - Published: Ignition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have...moreIgnition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have some part of each element’s name be the index. For example, you may have: strings/myAlarms/Alarm[0] , ../Alarm[1] , ../Alarm[2] , and ../Alarm[3] as an array of Alarm strings. While in this example they all exist in the one myAlarms folder, each element is an individual tag. So, if you want use Nod...... <less Mosquitto MQTT server in old cellphone Forum - Published: Hi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the...moreHi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the app Termux (linux terminal emulator) in order to run Mosquitto in the device, the PR1 nodered receives the data with no issues and I have performed intense testing and integrated with several devices. It works perfectly even with heavy loads and the built in battery gives me a lot of flexibility no...... <less « PreviousPage 2 of 6Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Radio button-like behavior Forum - Published: Greetings OptoFans, I recently had someone ask me for some sample code to make use of a loop in OptoScript. In his application, he has several user choices (in an integer table), and wants those...more Greetings OptoFans, I recently had someone ask me for some sample code to make use of a loop in OptoScript. In his application, he has several user choices (in an integer table), and wants those options to act like radio buttons. In other words, if one choice is selected, the others are de-selected. He originally solved this with multiple if statements but was looking for a loop option. Here’s his original code and my suggested loop. I’m hoping you Clever People Out There in OptoLand will have ...... <less Selecting a Solid state relay for a 1HP 120VAC motor Forum - Published: I have a customer with a 1HP 120VAC pump ùsing a smart device to time and control it. Another person has tried some generic 25A 250V and 40A 380V SSRs with all failure. One 25A unit faled-open, one...moreI have a customer with a 1HP 120VAC pump ùsing a smart device to time and control it. Another person has tried some generic 25A 250V and 40A 380V SSRs with all failure. One 25A unit faled-open, one failed-closed(shorted), and the 40A unit failed-closed. All had heat sinks with proper compound. I have assured this new customer that we can provide a reliable permanent solution, using an Opto22 product by an American company. What will be the best O22 SSR product to use for this application? And ...... <less Capture the edge of a state change Forum - Published: I develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a...moreI develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a comparison between LastState and the current value, if they are different I update the LastState variable to the current state and perform the required reaction. if ((InputPoint=1) and (LastState=0)) Then LastState=1; Perform whatever reaction should happen at the on edge elseif ((InputPoint=0) and (Last...... <less Groov Box Communication Error When Trying to read Static Tags Forum - Published: Getting this error when trying to access static tags in groov. How can I resolve this?... Getting this error when trying to access static tags in groov. How can I resolve this?... <less Long Epic Boot Time Forum - Published: First time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a...moreFirst time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a thin client as the HMI and I had to add an output that the strategy turns on to power the HMI when the EPIC was ready. The thin client boots much faster and can’t connect to the EPIC because it wasn’t ready. Now, though, the output comes on but the EPIC is still not ready so I have to add an additi...... <less FT232H to Flash Forum - Published: Hello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am...moreHello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am really trying to talk to the chip through a GROOV EPIC microcontroller through SSH PUTTY. Through this way, I can only get to trying to talk to the chip by git cloning to the site on putty through “git clone GitHub - optodeveloper/SSH-Demo” through that, I talked to the USB port through “/dev/ttyS...... <less What does "edge programmable" mean? Forum - Published: According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”....According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”.... <less Detect I/O Module Being Used Forum - Published: This may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module...moreThis may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module hardware currently connected to the Opto as possible. For analog cards I can retrieve the type/model of the module, whereas for digital it just says “Dig/None”. So I can’t get the model or even know if there is something connected in that slot. I saw an older post that seems to confirm that you just h...... <less MMP via Java? - old forum post Forum - Published: ashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the...moreashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the protocol for memory mapping using Java or if anyone knows where it can be found? I have started to duplicate it by going along with the c++ code from the toolkit but was wondering if there was an easier way to do it? Thanks Report 02-13-2009, 9:39 AM ben orchard Joined on 12-08-2004 Posts 33 Re: Java P...... <less Share data between EPICs (MQTT vs VPN)? Forum - Published: How do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very...moreHow do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very soon. For each facility, I have dashboard set up locally. These facilities, while they are remote, are connected to single VPN. We have HQ where our bosses sit. I plan to set up groov EPIC there to have a dashboard that will display data from remote facilities.... <less Read Entire Ignition Tag Arrays Using Loops & Dynamic Settings Forum - Published: Ignition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have...moreIgnition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have some part of each element’s name be the index. For example, you may have: strings/myAlarms/Alarm[0] , ../Alarm[1] , ../Alarm[2] , and ../Alarm[3] as an array of Alarm strings. While in this example they all exist in the one myAlarms folder, each element is an individual tag. So, if you want use Nod...... <less Mosquitto MQTT server in old cellphone Forum - Published: Hi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the...moreHi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the app Termux (linux terminal emulator) in order to run Mosquitto in the device, the PR1 nodered receives the data with no issues and I have performed intense testing and integrated with several devices. It works perfectly even with heavy loads and the built in battery gives me a lot of flexibility no...... <less « PreviousPage 2 of 6Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Selecting a Solid state relay for a 1HP 120VAC motor Forum - Published: I have a customer with a 1HP 120VAC pump ùsing a smart device to time and control it. Another person has tried some generic 25A 250V and 40A 380V SSRs with all failure. One 25A unit faled-open, one...moreI have a customer with a 1HP 120VAC pump ùsing a smart device to time and control it. Another person has tried some generic 25A 250V and 40A 380V SSRs with all failure. One 25A unit faled-open, one failed-closed(shorted), and the 40A unit failed-closed. All had heat sinks with proper compound. I have assured this new customer that we can provide a reliable permanent solution, using an Opto22 product by an American company. What will be the best O22 SSR product to use for this application? And ...... <less Capture the edge of a state change Forum - Published: I develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a...moreI develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a comparison between LastState and the current value, if they are different I update the LastState variable to the current state and perform the required reaction. if ((InputPoint=1) and (LastState=0)) Then LastState=1; Perform whatever reaction should happen at the on edge elseif ((InputPoint=0) and (Last...... <less Groov Box Communication Error When Trying to read Static Tags Forum - Published: Getting this error when trying to access static tags in groov. How can I resolve this?... Getting this error when trying to access static tags in groov. How can I resolve this?... <less Long Epic Boot Time Forum - Published: First time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a...moreFirst time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a thin client as the HMI and I had to add an output that the strategy turns on to power the HMI when the EPIC was ready. The thin client boots much faster and can’t connect to the EPIC because it wasn’t ready. Now, though, the output comes on but the EPIC is still not ready so I have to add an additi...... <less FT232H to Flash Forum - Published: Hello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am...moreHello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am really trying to talk to the chip through a GROOV EPIC microcontroller through SSH PUTTY. Through this way, I can only get to trying to talk to the chip by git cloning to the site on putty through “git clone GitHub - optodeveloper/SSH-Demo” through that, I talked to the USB port through “/dev/ttyS...... <less What does "edge programmable" mean? Forum - Published: According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”....According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”.... <less Detect I/O Module Being Used Forum - Published: This may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module...moreThis may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module hardware currently connected to the Opto as possible. For analog cards I can retrieve the type/model of the module, whereas for digital it just says “Dig/None”. So I can’t get the model or even know if there is something connected in that slot. I saw an older post that seems to confirm that you just h...... <less MMP via Java? - old forum post Forum - Published: ashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the...moreashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the protocol for memory mapping using Java or if anyone knows where it can be found? I have started to duplicate it by going along with the c++ code from the toolkit but was wondering if there was an easier way to do it? Thanks Report 02-13-2009, 9:39 AM ben orchard Joined on 12-08-2004 Posts 33 Re: Java P...... <less Share data between EPICs (MQTT vs VPN)? Forum - Published: How do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very...moreHow do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very soon. For each facility, I have dashboard set up locally. These facilities, while they are remote, are connected to single VPN. We have HQ where our bosses sit. I plan to set up groov EPIC there to have a dashboard that will display data from remote facilities.... <less Read Entire Ignition Tag Arrays Using Loops & Dynamic Settings Forum - Published: Ignition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have...moreIgnition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have some part of each element’s name be the index. For example, you may have: strings/myAlarms/Alarm[0] , ../Alarm[1] , ../Alarm[2] , and ../Alarm[3] as an array of Alarm strings. While in this example they all exist in the one myAlarms folder, each element is an individual tag. So, if you want use Nod...... <less Mosquitto MQTT server in old cellphone Forum - Published: Hi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the...moreHi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the app Termux (linux terminal emulator) in order to run Mosquitto in the device, the PR1 nodered receives the data with no issues and I have performed intense testing and integrated with several devices. It works perfectly even with heavy loads and the built in battery gives me a lot of flexibility no...... <less « PreviousPage 2 of 6Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Capture the edge of a state change Forum - Published: I develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a...moreI develop applications where I need to capture the edge of a state change. For example, when a discrete point changes from low to high. Currently I use a variable, which I call LastState. I do a comparison between LastState and the current value, if they are different I update the LastState variable to the current state and perform the required reaction. if ((InputPoint=1) and (LastState=0)) Then LastState=1; Perform whatever reaction should happen at the on edge elseif ((InputPoint=0) and (Last...... <less Groov Box Communication Error When Trying to read Static Tags Forum - Published: Getting this error when trying to access static tags in groov. How can I resolve this?... Getting this error when trying to access static tags in groov. How can I resolve this?... <less Long Epic Boot Time Forum - Published: First time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a...moreFirst time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a thin client as the HMI and I had to add an output that the strategy turns on to power the HMI when the EPIC was ready. The thin client boots much faster and can’t connect to the EPIC because it wasn’t ready. Now, though, the output comes on but the EPIC is still not ready so I have to add an additi...... <less FT232H to Flash Forum - Published: Hello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am...moreHello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am really trying to talk to the chip through a GROOV EPIC microcontroller through SSH PUTTY. Through this way, I can only get to trying to talk to the chip by git cloning to the site on putty through “git clone GitHub - optodeveloper/SSH-Demo” through that, I talked to the USB port through “/dev/ttyS...... <less What does "edge programmable" mean? Forum - Published: According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”....According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”.... <less Detect I/O Module Being Used Forum - Published: This may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module...moreThis may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module hardware currently connected to the Opto as possible. For analog cards I can retrieve the type/model of the module, whereas for digital it just says “Dig/None”. So I can’t get the model or even know if there is something connected in that slot. I saw an older post that seems to confirm that you just h...... <less MMP via Java? - old forum post Forum - Published: ashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the...moreashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the protocol for memory mapping using Java or if anyone knows where it can be found? I have started to duplicate it by going along with the c++ code from the toolkit but was wondering if there was an easier way to do it? Thanks Report 02-13-2009, 9:39 AM ben orchard Joined on 12-08-2004 Posts 33 Re: Java P...... <less Share data between EPICs (MQTT vs VPN)? Forum - Published: How do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very...moreHow do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very soon. For each facility, I have dashboard set up locally. These facilities, while they are remote, are connected to single VPN. We have HQ where our bosses sit. I plan to set up groov EPIC there to have a dashboard that will display data from remote facilities.... <less Read Entire Ignition Tag Arrays Using Loops & Dynamic Settings Forum - Published: Ignition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have...moreIgnition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have some part of each element’s name be the index. For example, you may have: strings/myAlarms/Alarm[0] , ../Alarm[1] , ../Alarm[2] , and ../Alarm[3] as an array of Alarm strings. While in this example they all exist in the one myAlarms folder, each element is an individual tag. So, if you want use Nod...... <less Mosquitto MQTT server in old cellphone Forum - Published: Hi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the...moreHi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the app Termux (linux terminal emulator) in order to run Mosquitto in the device, the PR1 nodered receives the data with no issues and I have performed intense testing and integrated with several devices. It works perfectly even with heavy loads and the built in battery gives me a lot of flexibility no...... <less « PreviousPage 2 of 6Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Groov Box Communication Error When Trying to read Static Tags Forum - Published: Getting this error when trying to access static tags in groov. How can I resolve this?... Getting this error when trying to access static tags in groov. How can I resolve this?... <less Long Epic Boot Time Forum - Published: First time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a...moreFirst time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a thin client as the HMI and I had to add an output that the strategy turns on to power the HMI when the EPIC was ready. The thin client boots much faster and can’t connect to the EPIC because it wasn’t ready. Now, though, the output comes on but the EPIC is still not ready so I have to add an additi...... <less FT232H to Flash Forum - Published: Hello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am...moreHello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am really trying to talk to the chip through a GROOV EPIC microcontroller through SSH PUTTY. Through this way, I can only get to trying to talk to the chip by git cloning to the site on putty through “git clone GitHub - optodeveloper/SSH-Demo” through that, I talked to the USB port through “/dev/ttyS...... <less What does "edge programmable" mean? Forum - Published: According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”....According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”.... <less Detect I/O Module Being Used Forum - Published: This may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module...moreThis may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module hardware currently connected to the Opto as possible. For analog cards I can retrieve the type/model of the module, whereas for digital it just says “Dig/None”. So I can’t get the model or even know if there is something connected in that slot. I saw an older post that seems to confirm that you just h...... <less MMP via Java? - old forum post Forum - Published: ashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the...moreashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the protocol for memory mapping using Java or if anyone knows where it can be found? I have started to duplicate it by going along with the c++ code from the toolkit but was wondering if there was an easier way to do it? Thanks Report 02-13-2009, 9:39 AM ben orchard Joined on 12-08-2004 Posts 33 Re: Java P...... <less Share data between EPICs (MQTT vs VPN)? Forum - Published: How do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very...moreHow do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very soon. For each facility, I have dashboard set up locally. These facilities, while they are remote, are connected to single VPN. We have HQ where our bosses sit. I plan to set up groov EPIC there to have a dashboard that will display data from remote facilities.... <less Read Entire Ignition Tag Arrays Using Loops & Dynamic Settings Forum - Published: Ignition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have...moreIgnition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have some part of each element’s name be the index. For example, you may have: strings/myAlarms/Alarm[0] , ../Alarm[1] , ../Alarm[2] , and ../Alarm[3] as an array of Alarm strings. While in this example they all exist in the one myAlarms folder, each element is an individual tag. So, if you want use Nod...... <less Mosquitto MQTT server in old cellphone Forum - Published: Hi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the...moreHi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the app Termux (linux terminal emulator) in order to run Mosquitto in the device, the PR1 nodered receives the data with no issues and I have performed intense testing and integrated with several devices. It works perfectly even with heavy loads and the built in battery gives me a lot of flexibility no...... <less « PreviousPage 2 of 6Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Long Epic Boot Time Forum - Published: First time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a...moreFirst time using an EPIC and the boot time seems way too long to me. It’s in the field and a technician just timed it at 3 minutes from startup to login screen on the built-in screen. We’re using a thin client as the HMI and I had to add an output that the strategy turns on to power the HMI when the EPIC was ready. The thin client boots much faster and can’t connect to the EPIC because it wasn’t ready. Now, though, the output comes on but the EPIC is still not ready so I have to add an additi...... <less FT232H to Flash Forum - Published: Hello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am...moreHello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am really trying to talk to the chip through a GROOV EPIC microcontroller through SSH PUTTY. Through this way, I can only get to trying to talk to the chip by git cloning to the site on putty through “git clone GitHub - optodeveloper/SSH-Demo” through that, I talked to the USB port through “/dev/ttyS...... <less What does "edge programmable" mean? Forum - Published: According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”....According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”.... <less Detect I/O Module Being Used Forum - Published: This may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module...moreThis may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module hardware currently connected to the Opto as possible. For analog cards I can retrieve the type/model of the module, whereas for digital it just says “Dig/None”. So I can’t get the model or even know if there is something connected in that slot. I saw an older post that seems to confirm that you just h...... <less MMP via Java? - old forum post Forum - Published: ashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the...moreashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the protocol for memory mapping using Java or if anyone knows where it can be found? I have started to duplicate it by going along with the c++ code from the toolkit but was wondering if there was an easier way to do it? Thanks Report 02-13-2009, 9:39 AM ben orchard Joined on 12-08-2004 Posts 33 Re: Java P...... <less Share data between EPICs (MQTT vs VPN)? Forum - Published: How do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very...moreHow do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very soon. For each facility, I have dashboard set up locally. These facilities, while they are remote, are connected to single VPN. We have HQ where our bosses sit. I plan to set up groov EPIC there to have a dashboard that will display data from remote facilities.... <less Read Entire Ignition Tag Arrays Using Loops & Dynamic Settings Forum - Published: Ignition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have...moreIgnition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have some part of each element’s name be the index. For example, you may have: strings/myAlarms/Alarm[0] , ../Alarm[1] , ../Alarm[2] , and ../Alarm[3] as an array of Alarm strings. While in this example they all exist in the one myAlarms folder, each element is an individual tag. So, if you want use Nod...... <less Mosquitto MQTT server in old cellphone Forum - Published: Hi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the...moreHi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the app Termux (linux terminal emulator) in order to run Mosquitto in the device, the PR1 nodered receives the data with no issues and I have performed intense testing and integrated with several devices. It works perfectly even with heavy loads and the built in battery gives me a lot of flexibility no...... <less « PreviousPage 2 of 6Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
FT232H to Flash Forum - Published: Hello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am...moreHello, I am trying to talk to a flash microchip (ST M25P16 200 mil SOIC-8) with the FT232H breakout board. This is what my board looks like: IMG_07834032×3024 2.79 MB IMG_07843024×4032 2.52 MB I am really trying to talk to the chip through a GROOV EPIC microcontroller through SSH PUTTY. Through this way, I can only get to trying to talk to the chip by git cloning to the site on putty through “git clone GitHub - optodeveloper/SSH-Demo” through that, I talked to the USB port through “/dev/ttyS...... <less What does "edge programmable" mean? Forum - Published: According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”....According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”.... <less Detect I/O Module Being Used Forum - Published: This may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module...moreThis may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module hardware currently connected to the Opto as possible. For analog cards I can retrieve the type/model of the module, whereas for digital it just says “Dig/None”. So I can’t get the model or even know if there is something connected in that slot. I saw an older post that seems to confirm that you just h...... <less MMP via Java? - old forum post Forum - Published: ashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the...moreashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the protocol for memory mapping using Java or if anyone knows where it can be found? I have started to duplicate it by going along with the c++ code from the toolkit but was wondering if there was an easier way to do it? Thanks Report 02-13-2009, 9:39 AM ben orchard Joined on 12-08-2004 Posts 33 Re: Java P...... <less Share data between EPICs (MQTT vs VPN)? Forum - Published: How do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very...moreHow do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very soon. For each facility, I have dashboard set up locally. These facilities, while they are remote, are connected to single VPN. We have HQ where our bosses sit. I plan to set up groov EPIC there to have a dashboard that will display data from remote facilities.... <less Read Entire Ignition Tag Arrays Using Loops & Dynamic Settings Forum - Published: Ignition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have...moreIgnition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have some part of each element’s name be the index. For example, you may have: strings/myAlarms/Alarm[0] , ../Alarm[1] , ../Alarm[2] , and ../Alarm[3] as an array of Alarm strings. While in this example they all exist in the one myAlarms folder, each element is an individual tag. So, if you want use Nod...... <less Mosquitto MQTT server in old cellphone Forum - Published: Hi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the...moreHi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the app Termux (linux terminal emulator) in order to run Mosquitto in the device, the PR1 nodered receives the data with no issues and I have performed intense testing and integrated with several devices. It works perfectly even with heavy loads and the built in battery gives me a lot of flexibility no...... <less « PreviousPage 2 of 6Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
What does "edge programmable" mean? Forum - Published: According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”....According to a recent webinar, groov EPIC is “Edge Programmable”. What does edge programmable mean? I cannot find a definition of “edge programmable” or “edge programming”.... <less Detect I/O Module Being Used Forum - Published: This may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module...moreThis may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module hardware currently connected to the Opto as possible. For analog cards I can retrieve the type/model of the module, whereas for digital it just says “Dig/None”. So I can’t get the model or even know if there is something connected in that slot. I saw an older post that seems to confirm that you just h...... <less MMP via Java? - old forum post Forum - Published: ashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the...moreashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the protocol for memory mapping using Java or if anyone knows where it can be found? I have started to duplicate it by going along with the c++ code from the toolkit but was wondering if there was an easier way to do it? Thanks Report 02-13-2009, 9:39 AM ben orchard Joined on 12-08-2004 Posts 33 Re: Java P...... <less Share data between EPICs (MQTT vs VPN)? Forum - Published: How do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very...moreHow do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very soon. For each facility, I have dashboard set up locally. These facilities, while they are remote, are connected to single VPN. We have HQ where our bosses sit. I plan to set up groov EPIC there to have a dashboard that will display data from remote facilities.... <less Read Entire Ignition Tag Arrays Using Loops & Dynamic Settings Forum - Published: Ignition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have...moreIgnition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have some part of each element’s name be the index. For example, you may have: strings/myAlarms/Alarm[0] , ../Alarm[1] , ../Alarm[2] , and ../Alarm[3] as an array of Alarm strings. While in this example they all exist in the one myAlarms folder, each element is an individual tag. So, if you want use Nod...... <less Mosquitto MQTT server in old cellphone Forum - Published: Hi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the...moreHi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the app Termux (linux terminal emulator) in order to run Mosquitto in the device, the PR1 nodered receives the data with no issues and I have performed intense testing and integrated with several devices. It works perfectly even with heavy loads and the built in battery gives me a lot of flexibility no...... <less « PreviousPage 2 of 6Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Detect I/O Module Being Used Forum - Published: This may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module...moreThis may cross over with applications, but maybe not. If this is the wrong category I’ll repost it. Anyway, I’m working on an application and I’d like to gather as much information about the module hardware currently connected to the Opto as possible. For analog cards I can retrieve the type/model of the module, whereas for digital it just says “Dig/None”. So I can’t get the model or even know if there is something connected in that slot. I saw an older post that seems to confirm that you just h...... <less MMP via Java? - old forum post Forum - Published: ashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the...moreashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the protocol for memory mapping using Java or if anyone knows where it can be found? I have started to duplicate it by going along with the c++ code from the toolkit but was wondering if there was an easier way to do it? Thanks Report 02-13-2009, 9:39 AM ben orchard Joined on 12-08-2004 Posts 33 Re: Java P...... <less Share data between EPICs (MQTT vs VPN)? Forum - Published: How do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very...moreHow do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very soon. For each facility, I have dashboard set up locally. These facilities, while they are remote, are connected to single VPN. We have HQ where our bosses sit. I plan to set up groov EPIC there to have a dashboard that will display data from remote facilities.... <less Read Entire Ignition Tag Arrays Using Loops & Dynamic Settings Forum - Published: Ignition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have...moreIgnition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have some part of each element’s name be the index. For example, you may have: strings/myAlarms/Alarm[0] , ../Alarm[1] , ../Alarm[2] , and ../Alarm[3] as an array of Alarm strings. While in this example they all exist in the one myAlarms folder, each element is an individual tag. So, if you want use Nod...... <less Mosquitto MQTT server in old cellphone Forum - Published: Hi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the...moreHi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the app Termux (linux terminal emulator) in order to run Mosquitto in the device, the PR1 nodered receives the data with no issues and I have performed intense testing and integrated with several devices. It works perfectly even with heavy loads and the built in battery gives me a lot of flexibility no...... <less « PreviousPage 2 of 6Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
MMP via Java? - old forum post Forum - Published: ashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the...moreashby85 Joined on 01-06-2009 Posts 2 Java Protocol I have been looking at using Java as an HMI for an application. I am using an R1 controller and was wondering if anyone else has duplicated the protocol for memory mapping using Java or if anyone knows where it can be found? I have started to duplicate it by going along with the c++ code from the toolkit but was wondering if there was an easier way to do it? Thanks Report 02-13-2009, 9:39 AM ben orchard Joined on 12-08-2004 Posts 33 Re: Java P...... <less Share data between EPICs (MQTT vs VPN)? Forum - Published: How do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very...moreHow do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very soon. For each facility, I have dashboard set up locally. These facilities, while they are remote, are connected to single VPN. We have HQ where our bosses sit. I plan to set up groov EPIC there to have a dashboard that will display data from remote facilities.... <less Read Entire Ignition Tag Arrays Using Loops & Dynamic Settings Forum - Published: Ignition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have...moreIgnition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have some part of each element’s name be the index. For example, you may have: strings/myAlarms/Alarm[0] , ../Alarm[1] , ../Alarm[2] , and ../Alarm[3] as an array of Alarm strings. While in this example they all exist in the one myAlarms folder, each element is an individual tag. So, if you want use Nod...... <less Mosquitto MQTT server in old cellphone Forum - Published: Hi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the...moreHi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the app Termux (linux terminal emulator) in order to run Mosquitto in the device, the PR1 nodered receives the data with no issues and I have performed intense testing and integrated with several devices. It works perfectly even with heavy loads and the built in battery gives me a lot of flexibility no...... <less « PreviousPage 2 of 6Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Share data between EPICs (MQTT vs VPN)? Forum - Published: How do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very...moreHow do I share data between groov EPICs that are located remotely? Right now, we have two facilities with groov EPIC installed, collecting data 24/7. We plan to add groov EPIC to other facilities very soon. For each facility, I have dashboard set up locally. These facilities, while they are remote, are connected to single VPN. We have HQ where our bosses sit. I plan to set up groov EPIC there to have a dashboard that will display data from remote facilities.... <less Read Entire Ignition Tag Arrays Using Loops & Dynamic Settings Forum - Published: Ignition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have...moreIgnition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have some part of each element’s name be the index. For example, you may have: strings/myAlarms/Alarm[0] , ../Alarm[1] , ../Alarm[2] , and ../Alarm[3] as an array of Alarm strings. While in this example they all exist in the one myAlarms folder, each element is an individual tag. So, if you want use Nod...... <less Mosquitto MQTT server in old cellphone Forum - Published: Hi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the...moreHi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the app Termux (linux terminal emulator) in order to run Mosquitto in the device, the PR1 nodered receives the data with no issues and I have performed intense testing and integrated with several devices. It works perfectly even with heavy loads and the built in battery gives me a lot of flexibility no...... <less « PreviousPage 2 of 6Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Read Entire Ignition Tag Arrays Using Loops & Dynamic Settings Forum - Published: Ignition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have...moreIgnition EDGE stores data with each piece of information being held in one tag. Depending on the application that sets the tags, it may organize arrays of data into subfolders, and will typically have some part of each element’s name be the index. For example, you may have: strings/myAlarms/Alarm[0] , ../Alarm[1] , ../Alarm[2] , and ../Alarm[3] as an array of Alarm strings. While in this example they all exist in the one myAlarms folder, each element is an individual tag. So, if you want use Nod...... <less Mosquitto MQTT server in old cellphone Forum - Published: Hi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the...moreHi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the app Termux (linux terminal emulator) in order to run Mosquitto in the device, the PR1 nodered receives the data with no issues and I have performed intense testing and integrated with several devices. It works perfectly even with heavy loads and the built in battery gives me a lot of flexibility no...... <less « PreviousPage 2 of 6Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items
Mosquitto MQTT server in old cellphone Forum - Published: Hi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the...moreHi, Simple tip, if you need to test MQTT related projects with your PR-1 without running Mosquitto on the PR1 (risky) or using a PC? I have used and old motorolla G4+ cell phone android 7, running the app Termux (linux terminal emulator) in order to run Mosquitto in the device, the PR1 nodered receives the data with no issues and I have performed intense testing and integrated with several devices. It works perfectly even with heavy loads and the built in battery gives me a lot of flexibility no...... <less « PreviousPage 2 of 6Next » Show 25 Items Show All Items Show 10 Items Show 25 Items Show 50 Items Show 100 Items